manualshive.com logo in svg

KSB Etanorm FXV, Инструкция по установке и эксплуатации

Поделиться
Скачать
KSB Etanorm FXV Скачать руководство пользователя страница 11

3 Transport/Storage/Disposal

11 of 62

Etanorm FXV

1311.83/06-EN

3 Transport/Storage/Disposal

3.1 Checking the condition upon delivery

1. On transfer of goods, check each packaging unit for damage.

2. In the event of in-transit damage, assess the exact damage, document it and

notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.

3.2 Transport

 DANGER

The pump (set) could slip out of the suspension arrangement

Danger to life from falling parts!

▷

Always transport the pump (set) in the specified position.

▷

Never attach the suspension arrangement to the free shaft end or the motor
eyebolt.

▷

Observe the information about weights, centre of gravity and fastening points.

▷

Observe the applicable local accident prevention regulations.

▷

Use suitable, permitted lifting accessories, e.g. self-tightening lifting tongs.

To transport the pump/pump set or back pull-out unit suspend it from the lifting
tackle as shown.

Fig. 1: 

Transporting the back pull-out unit

Fig. 2: 

Transporting the pump

≤ 90 °

Fig. 3: 

Transporting the pump set

Содержание Etanorm FXV































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды