KSB AmaSlide KB16-AH280 Скачать руководство пользователя страница 11

Страница: 11 / 32

3 Transport/Storage/Disposal

11 of 32

AmaSlide

2553.870/01-EN

Table 4:

Ambient conditions for storage

Ambient condition

Value

Relative humidity

Max. 85 % (non-condensing)

Ambient temperature

-20 °C to +80 °C

-4 °F to +176 °F

▪

Store the maintenance aid in dry, vibration-free conditions, and protect it against
the weather.

▪

Store the maintenance aid in a dry room in which the atmospheric humidity is
maintained at a constant level.

▪

Prevent excessive fluctuations in atmospheric humidity (see table Ambient
conditions for storage).

If stored properly, the product will be protected for a maximum of 12 months.

Preservation

Preservation will protect the maintenance aid against corrosion if it is stored or taken
out of service for a prolonged period of time.

WARNING

Fluids, consumables and supplies posing a health hazard

Hazard to persons and the environment!

▷

Collect and dispose of any preservatives, flushing liquids and fluid residues.

▷

Wear safety clothing and a protective mask, if required.

▷

Observe all legal regulations on the disposal of fluids posing a health hazard.

NOTE

Observe the manufacturer's instructions for application/removal of the preservative.

1. Thoroughly clean the maintenance aid.

2. Apply the preservative evenly.

Removal of preservation

Preservatives must be removed from the maintenance aid prior to commissioning.

WARNING

Fluids, consumables and supplies posing a health hazard

Hazard to persons and the environment!

▷

Collect and dispose of any preservatives, flushing liquids and fluid residues.

▷

Wear safety clothing and a protective mask, if required.

▷

Observe all legal regulations on the disposal of fluids posing a health hazard.

NOTE

Observe the manufacturer's instructions for application/removal of the preservative.

3.4 Return to supplier

1. Prior to returning the product to the supplier, flush and clean it, particularly if it

has been used in noxious, explosive, hot or other hazardous fluids.

2. If the product has been used in fluids whose residues could lead to corrosion

damage in the presence of atmospheric humidity or could ignite upon contact
with oxygen, the product must also be neutralised and treated with anhydrous
inert gas to ensure drying.

3. Always complete and enclose a certificate of decontamination when returning

the product. (

Section 9, Page 30)

Indicate any safety measures and decontamination measures taken.

Содержание AmaSlide KB16-AH280

































Результаты поиска

Содержание AmaSlide KB16-AH280

Отзывы:

Похожие инструкции для AmaSlide KB16-AH280

Бренды по названию

Популярные бренды

KSB AmaSlide KB16-AH280, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AmaSlide KB16-AH280

Отзывы:

Похожие инструкции для AmaSlide KB16-AH280

Бренды по названию

Популярные бренды