Krone Comprima F 125 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 430

Krone Comprima F 125 Скачать руководство пользователя страница 115

Driving and Transport

115

Pos: 46.1 /Überschriften/Überschriften 1/F-J/F ahr en und Transport @ 0\mod_1196330049217_78.docx @ 6553 @ 1 @ 1

10

Driving and Transport

Pos: 46.2 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/Warnung - Str aßenfahrt R undball enpressen @ 388\mod_1445353464942_78.docx @ 2779427 @ @ 1

WARNING!
Risk of accident and injury or damage to the machine!

If the general traffic regulations and the following rules for road travel with agricultural machines

are not met, persons could hurt and/or the machine could be damaged.
•  Note basic safety instructions on “Dangers in road travel” in chapter entitled Safety.
•  On public roads, only drive with empty and closed bale chamber.
•  Raise and secure blade cassette.
•  Switch off the operation unit in order to avoid that functions are accidentally triggered.

Pos: 46.3 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG - Nichtbeachtung der grundl egenden Sicherheitshinweise alte F orm @ 254\mod_1397485793575_78.docx @ 1953347 @ @ 1

WARNING!
If the basic safety instructions are not followed, people may be seriously injured or
killed.

• To avoid accidents, the basic safety instructions in the chapter Safety must have been

read and followed, see chapter Safety "Basic safety instructions".

Pos: 46.4 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG - Nichtbeachtung der Sicherheitsr outinen al te For m @ 273\mod_1404117435996_78.docx @ 2058712 @ @ 1

WARNING!
If the safety routines are not adhered to, people may be seriously injured or killed.

• To avoid accidents, the safety routines in the chapter Safety must be read and followed,

see chapter Safety "Safety routines".

Pos: 46.5 /BA/Sicher heit/Fahren und Transport/Warnung - Straß enfahrt U nfallgefahr durch nicht verriegelte Steuer ventil e des Traktors @ 274\mod_1404213302399_78.docx @ 2060724 @ @ 1

WARNING!
There is a risk of accidents if the control valves on the tractor are not locked.

If the control valves are not locked, machine components may be activated unintentionally. This

can result in serious accidents.
• To prevent functions being triggered accidentally, the control valves on the tractor must be

switched to neutral and locked during road transport journeys.

Pos: 46.6 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/Warnung - Gefahr en bei Kur venfahrten mi t ang ehängter M aschine @ 273\mod_1403678392890_78.docx @ 2053902 @ @ 1

WARNING!
Danger when cornering with a machine hitched

When cornering, the hitched machine swings out further than the tractor. This can lead to

accidents.
• Take the greater swivel range into account.
• When turning, take account of people, oncoming traffic and obstacles.

Pos: 46.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
113
114
115
116
117
...
»

Содержание Comprima F 125















































































































































































































































































































































































































































Отзывы:

Нет отзывов