Maintenance
53
Pos: 29.24.1 /Ü berschriften/Ü berschriften 2/K-O/OÖlstandskontr olle und Öl wechsel am M ähhol m @ 0\mod_1197017549815_78.docx @ 15963 @ 2 @ 1
10.7
Oil level check and oil change on the cutter bar
Pos: 29.24.2 /Ü berschriften/Ü berschriften 3/K-O/OÖl wechsel @ 0\mod_1197021941955_78.docx @ 16139 @ 3 @ 1
10.7.1
Oil change
Pos: 29.24.3 /BA/Wartung/Mähwerke/Hi nweis Ei n Öl wechsel am M ähhol m ist nicht erfor derlich. @ 68 \mod_1304577391388_78.docx @ 628708 @ @ 1
Note
No oil change is required on the cutter bar.
Pos: 29.24.4 /Ü berschriften/Ü berschriften 3/K-O/OÖl kontroll e @ 0\mod_1197021908190_78.docx @ 16120 @ 3 @ 1
10.7.2
Checking the oil level
Pos: 29.24.5 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M esser trommel_2 @ 0\mod_1197022569252_78.docx @ 16165 @ @ 1
Danger! - Rapidly rotating cutting discs/blade drums.
Effect: Danger to life or serious injuries.
Lower guards. Nobody should be in the danger zone around the machine.
Pos: 29.24.6 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M esser trommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1
Danger! - Rapidly rotating cutting discs/blade drums.
Effect: Danger to life or serious injuries.
• Switch off the engine and remove the ignition key.
• The cutting discs/blade drums continue to run!
• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete
stop.
Pos: 29.24.7 /BA/Sicherheit/6. Überar beitete Warnhinweise/Hinweis - Ver weis auf Anziehdrehmomente Verschlussschr auben @ 469\mod_1470667868238_78.docx @ 3167926 @ @ 1
Note
Tighten the locking screws on the gearboxes with the prescribed tightening torques, refer to
chapter Maintenance “Tightening Torques for Locking Screws and Bleed Valves on
Gearboxes”.
Pos: 29.24.8 /BA/Wartung/Mähwerke/AM Baurei he/Vor ber eitung Öl kontroll e / Öl wechel AM-S Baur eihe @ 70\mod_1305117991534_78.docx @ 634930 @ @ 1
• Allow the machine to run briefly
• Turn off the PTO
• Wait until cutting discs/blade drums have come to a complete stop
• Move the cutter bar into transport position
• Switch off the tractor engine and remove the ignition key
• Close the shut-off valve on the hydraulic cylinder of the disc mower
Pos: 29.24.9 /BA/Wartung/Mähwerke/Öl kontrolle / Öl wechsel M ähhol m AM- S Baurei he Bil d @ 73\mod_1307601585937_78.docx @ 652647 @ @ 1
Fig. 26
Pos: 29.24.10 /BA/Wartung/M ähwer ke/Öl kontr olle M ähholm AM- S / AM-CV Baureihe @ 70\mod_1305115617542_78.docx @ 634784 @ @ 1
Check the oil level before every use
• Remove the oil level inspection screw (1) from the cutter bar
• The oil level must be up to the bore hole. If necessary, top up the oil (SAE 90)
• Screw in the oil level inspection screw (1) again and tighten securely
Pos: 29.25 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1
Содержание AM 203 S
Страница 2: ...Table of Contents 2 Pos 2 Layout Modul e Seitenumbruch 0 mod_1196175311226_0 docx 4165 1 ...
Страница 73: ......
