manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 295 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 295

 

Settings

 

295 

 

Pos: 93.89 /Ü berschriften/Ü berschriften 2/P-T/SSchni ttlänge ei nstellen @ 275\mod_1404396419814_78.docx @ 2067708 @ 2 @ 1 

 

19.18 

Adjusting the chop length  

Pos: 93.90 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Schnittl äng e einstell en: Allgemein von der linken Seite Big Pack @ 279\mod_1405066787213_78.docx @ 2147503 @  @ 1 

 

The chop length is set in the same way on the right and left side of the machine. The setting 

procedure on the left side of the machine is described below. The same applies for the right 

side of the machine. 

Pos: 93.91 /BA/Ei nstellungen/Schneidwer k/Schnittlänge  ei nstellen/Voll bestückung/Bei Voll bestückung der M esser kassette @ 275\mod_1404456429078_78.docx @ 2068551 @  @ 1 

 

If the knife drawers are fully equipped 

Pos: 93.92 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Schnittl äng e  einstell en Bild @ 275\mod_1404399343354_78.docx @ 2067944 @  @ 1 

 

4

BPHS0299

 

Fig. 220 

Pos: 93.93 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Das Hilfswer kzeug ( 4) befi ndet sich an der linken Maschi nenseite, i n N ähe des Schneidwer ks. @ 275\mod_1404456286163_78.docx @ 2068523 @  @ 1 

 

The special tool (4) is to be found on the left-hand side of the machine, near the cutting system. 

Pos: 93.94 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Schnittl äng e einstell en T1 in Abhängig kei t der M esserschaltung @ 275\mod_1404399346135_78.docx @ 2067973 @  @ 1 

 

To set different chop lengths when the cutting system is fully equipped, the upper and lower 

knife selections (1, 2) must be in different positions (

 

/ 

) relative to one another. Chop 

length depending on the knife selection, see table. 

 

Pos: 93.95 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Schnittl äng e T abelle Messerschaltung BigPack  mit 16 Messer  @ 275\mod_1404400014028_78.docx @ 2067998 @  @ 1 

 

 

Table chop length depending on the knife selection (when fully equipped) 

Chop length 

mm 

Number of  

blades 

Upper knife selection 

Lower knife selection 

- 

0 

 

 

88 

8 

 

 

88 

8 

 

 

44 

16 

 

 

 

Pos: 93.96 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/Schnittl äng e einstell en T2 @ 275\mod_1404394430217_78.docx @ 2067736 @  @ 1 

 

•  Shut down and safeguard the machine, see chapter Safety -> Safety routines "Shutting 

down and safeguarding the machine". 

•  Attach the special tool (4) to the upper or knife selection (1, 2). 
 

CAUTION!

 Risk of injury due to spring pressure on the special tool. If you release it too soon, 

you can injure yourself. 

 

•  Turn the special tool (4) until the cams on the knife selection are either in the (

) position 

or in the (

) position. 

Pos: 93.97 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов