KRESS KUC60, Оригинальное руководство пользователя

Страница: 8 / 80

8
EN
Charger(KAC21) 1 1 /
We recommend that you purchase your accessories
listed in the above list from the same store that sold you
the tool. Refer to the accessory packaging for further
details. Store personnel can assist you and offer advice.
NOISE INFORMATION
A weighted sound pressure L
pA
: 78.1dB(A)
A weighted sound power L
wA
: 89.1dB(A)
K
PA
& K
WA
3dB(A)
Wear ear protection.
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined
according to EN 60745:
Hammer drilling into
concrete
Vibration emission value
a
h,HD
= 11.372 m/s
2
Uncertainty K
K = 1.5 m/s²
Chiseling
Vibration emission value
a
h,CHeq
= 9.393 m/s 2
Uncertainty K
K = 1.5 m/s²
The declared vibration total value may be used for
comparing one tool with another, and may also be used
in a preliminary assessment of exposure.
WARNING: The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the tool
is used dependant on the following examples and other
variations on how the tool is used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained
Using the correct accessory for the tool and ensuring it
is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
OPERATION GUIDELINES
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for hammer drilling and
chiseling in concrete, brick. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
BEFORE PUTTING INTO
OPERATION
A) CHARGING THE BATTERY PACK
The battery pack charger supplied is matched to the
Li-ion battery installed in the machine. Do not use
another battery charger.
The Li-ion battery pack is protected against deep
discharging. When the battery pack is empty, the
machine is switched off by means of a protective
circuit: The chuck no longer rotates.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging.
Allow time for the battery pack to cool down before
recharging.
When the battery pack is charged for the first time and
after prolonged storage. The battery pack will accept
a 100% charge after several charge and discharge
cycles.
B) TO REMOVE OR INSTALL BATTERY PACK (SEE
FIG. A)
Depress the battery pack release button to release
and slide the battery pack out from your tool. After
recharge, slide it back into your tool. A simple push
and slight pressure will be sufficient.
OPERATION
1. INSERTING AND REMOVING DRILL BIT IN SDS
Take care that the dust protection cap (2) is not
damaged when changing tools.
— INSERTING
Clean and lightly oil the bit before inserting. Insert the
dust-free bit into the bit holder with a twisting motion
until it latches.
The bit locks itself. Check the locking by pulling on
the tool.
— REMOVING
Retract back the bit holder locking sleeve (3) and pull
out the bit.