KRESS KUC35, Инструкция по безопасности и эксплуатации

Страница: 12 / 16

12
Lithium-Ion brushless hammer drill
KUC35 KUC35.9 KUC35.91
TORQUE ADJUSTMENT
SCREWDRIVING 1-20
DRILLING
HAMMER DRILLING
See Fig. E
Operating the on/off switch
Warning: Do not operate
for long periods at low
speed because excess heat will
be produced internally.
See Fig. F
LED light indicator
Before operation, the LED light
will be activated when the On/Off
switch is slightly pressed, and will
automatically turn off 20 seconds
after the On/Off switch is released.
The tool and battery are equipped
with a protection system. When
the LED Light is quickly flashing 3
seconds and turn off, the system will
automatically cut off power to the tool
to extend battery life. The tool will
automatically stop during operation
if the tool and/or battery are placed
under one of the following conditions:
• Overloaded: The tool is
operated in a manner that causes
it to draw an abnormally high
current. In this situation, release
the Trigger Switch on the tool and
stop the application that caused
the tool to become overloaded.
Then pull the Trigger Switch again
to restart.
• Overheated: Under the
condition above, if the tool does
not start, the Tool and Battery are
overheated. In this situation, let
the Tool and Battery cool before
pulling the Trigger Switch again.
• Low battery voltage: The
remaining Battery capacity is too
low and the tool will not operate.
In this situation, remove and
recharge the Battery.
Warning: To turn on the light,
press the On/Off switch and
make sure the Forward/Reverse
Rotation Control is on right/left
position.
ASSEMBLY
Note: Always power off the tool and remove the
battery pack before performing any assembly
operations on the tool.
Be sure to use the side handle (auxiliary
handle) for safe operations.
1. Install the side handle (auxiliary handle) (see
fig. G)
Firstly, rotate the handle counterclockwise relative to the
outer jaw
①
to separate the jaws
②
, then hold the outer
jaw
①
, stick the jaws
②
in the grooves
③
on the left and
right sides of the reducer, hold the outer jaw
①
with one
hand, and rotate the handle clockwise relative to the outer
jaw
①
to tighten it until the jaws
① ②
are fixed with the
grooves
③
tightly.
2. Remove the side handle (auxiliary handle)
(see fig. H)
Place the tool on the workbench, hold the outer jaw
①
with one hand, rotate the handle counterclockwise rela-
tive to the outer jaw
①
until the jaws
②
are loose, and
then remove them from the reducer grooves
③
.
ANTI-SPRAIN FUNCTION
The power tool will shut down quickly, when drill body
suddenly rotates around the bit due to blockage dur-
ing drilling. When the quick shutdown function is in
effect, the LED light will first flash twice slowly and then
flash every 1.5s circularly. Once the On/Off Switch is
released, the LED light stops flashing.
Press the On/Off Switch again to restart the tool.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The Forward and Reverse Switch, which is on top of
the trigger, is positioned in the lock function. Unlock the
Forward and Reverse Switch putting it into the required
rotation position. Push the trigger and the drill will start
to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the Torque Adjustment
Ring, you can find the Torque Adjustment Ring between
the Chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 20 is the
highest torque (screw driving force). Position is for
drill operation. Position is for hammer drill operation.
Regulate the Torque Adjustment Ring to a higher
position to reach the best result.
3. I CAN NOT FIT THE BATTERY INTO THE
BATTERY CHARGER. WHY?
The battery can be inserted into the charger only in one
direction. Turn the battery around until it can be inserted
into the slot, the red LED Light should turn on when the
battery is charging.
4. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIMES
Charging time problems, as above, and having not used
a Battery Pack for a prolonged time will reduce the
Battery Pack working time. This can be corrected after