background image

English

9

For drilling work in metal, wood and plastic with drills 
that have normal shafts, a drill chuck (13 mm max. 
chuck opening) is available. The drill chuck is 
mounted on the adapter (accessory) for screwdriver 
bits.  All common drill chucks with 1/2" x 20 UNF inter-
nal threads (13 mm max. chuck opening) can be 
used.

MOUNTING THE CHUCK

Before any work on the machine itself, pull the 
mains plug!

Clean the threads of the drill chuck (accessory) and 
the adapter 13 (accessory). Screw the drill chuck onto 
the adapter and tighten firmly (approx. 30 Nm). Clamp 
in a vise for tightening the adapter, for example. 
Clamp an Allen key in the drill chuck and use it to 
tighten the chuck. Then lock the adapter in the tool 
holder the same as a drill.

Do not drill into hidden electrical 
lines or gas and water pipes. 
Check the area to be worked with 
a metal detector, for example, 
before starting.

For metal, use only flawless, sharpened drills; for 
stone and concrete, only masonry drills with hard 
metal inserts.

Always adapt the speed to the material to be worked 
and the diameter of the drill. For precision working 
with metal and wood, place the machine in a drill 
stand (accessory).

HAMMER- DRILLING

Wear protective glasses and 
hearing protection.

Do not apply to much pressure. The performance is 
not increased in this manner.

For hammer drilling, work only with protective 
glasses, hearing protection and the auxiliary han-
dle 12. Check before putting into operation if the 
shift knob 10 is latched in the 

 position.

DRILLING IN TILES

Start drilling slowly on the tile. After the tile is drilled 
through, switch to impact drilling.

SCREWDRIVING

Screwdriver bits can be inserted into the adapter 13 
(accessory).  Commercially available bits with a hex-
agonal dimension of 6.3 mm or 1/4" (DIN 3126, 
Form C) can be used. 

The screwdriver bits are held in the adapter with a 
spring ring. Therefore, use only bits with a notch.

If the drilling tool become jammed or get caught, the 
slip clutch releases.

Remove the load from the machine immediately by 
pulling back the drilling tool.

Always hold the machine tightly with both hands and 
assume a secure stance.

Before any work on the machine itself, pull the 
mains plug!

Always keep the ventilation slots clean.

Wipe off the accessible plastic parts regularly with a 
cloth without cleaning agent.

After heavy use over a long period, the machine 
should be taken to a Kress service location for an 
inspection and thorough cleaning.

8

Drill Chuck (Accessory)

9

Practical Tips

10 Slip Clutch

11 Maintenance Measures

12 Environmental Protection

PH 500 - GB  Seite 9  Montag, 17. September 2001  1:20 13

Recycle raw materials instead of dis-

-

 

The machine, accessories and packa- 

ging should be sorted for environ-

mental friendly recycling.

Subject to change without notice

recycling

.

recycled paper 

These instructions are printed on

 

The plastic components are labelled for categorised

manufactured without chlorine.

together with household waste

 

material!

 

Do not dispose of electric tools 

posing as waste.

Содержание HM 550



















Отзывы: