manualshive.com logo in svg

KRAL CGF, Руководство по эксплуатации

Поделиться
Скачать
KRAL CGF Скачать руководство пользователя страница 57

16 Spare parts

16.2 Overview of CLE 851, CLE 951 – 3550 (inner bearing)

16.2 Overview of CLE 851, CLE 951 – 3550 (inner bearing)

661.2

739.2

131

1037

879.1

074

915.2

879.2

817

222.1

056.2

457

222.2

454*

739.1

041

134

428

739.3

866

915.3

884° 097

165

915.1

869.1

661.1

745

745

054 056.1

056.1

222.3*

869.2

Fig. 18: Spare parts CLE 851, CLE 951 – 3550

Qty.

Item No.

Part

Qty.

Item No.

Part

1

041

Distance sleeve

1

739.1

O-ring

2

054

Distance ring

1

739.2

O-ring

2

056.1

Supporting ring

1

739.3

O-ring

1

056.2

Supporting ring

2

745

Radial shaft seal ring

1

074

Flange cover

1

817

Ball bearing

1

097

Seal flange

1

866

Feather key

1

131

Cartridge housing

1

869.1

Circlip

1

134

Seal housing

1

869.2

Circlip

1

165

Screw plug

1

879.1

Straight pin

1

222.1

Flat gasket

1

879.2

Straight pin

1

222.2

Flat gasket

1

884

°

Threaded pin

1

222.3

*

Flat gasket

6/8/10

915.1

Socket screw

1

428

**

Counter-pressure valve

2

915.2

Socket screw

2

454*

Edge sealing ring

4

915.3

Socket screw

1

457

Mechanical seal

1

1037

Bearing bush set

1

661

Screw set

1

Silicone grease 1 g

*

Only for Size 2250 – 3550

**

Only for pumps with inlet pressure under the ambient pressure, only pumps with mechanical seal

°

Only for mechanical seal

Tab. 17: Spare parts CLE 851, CLE 951 – 3550

Operating instructions

OIC 18en-GB Edition 2020-01

57

Содержание CGF

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды