manualshive.com logo in svg

KRAL CGF, Руководство по эксплуатации

Поделиться
Скачать
KRAL CGF Скачать руководство пользователя страница 56

16 Spare parts

16.1 Overview of CLE 15 – 660, CLE 880 (inner bearing)

16 Spare parts

16.1 Overview of CLE 15 – 660, CLE 880 (inner bearing)

661.2

739.2

131

1037

739.1

222.2

859.2

074

915.2

859.3

428**

042

817

222.1

056.3

056.2

869

745.1

735*

915.1

866

134

165

859.1°

746

745.2

661.1

869.2

457

457

454

745.1

054

056.1

056.1

056.3

869.2

Fig. 17: Spare parts CLE 15 – 660, CLE 880

Qty.

Item No.

Part

Qty.

Item No.

Part

1

042

Balancing cylinder

1

739.1

O-ring

2

054

Distance ring

1

739.2

O-ring

2

056.1

Supporting ring

2

745.1

Radial shaft seal ring

1

056.2

Supporting ring

1

745.2

Radial shaft seal ring

1

056.3

Supporting ring

1

746

Throttle ring

1

074

Flange cover

1

817

Ball bearing

1

131

Cartridge housing

1

859.1°

Adapter sleeve

1

134

Seal housing

1

859.2

Adapter sleeve

2

165

Screw plug

1

859.3

Adapter sleeve

1

222.1

Flat gasket

1

866

Feather key

1

222.2

Flat gasket

1

869

Circlip

1

428**

Counter-pressure valve

1

869.2

Circlip

2

454

Edge sealing ring

4

915.1

Socket screw

1

457

Mechanical seal

4

915.2***

Socket screw

1

661

Screw set

1

1037

Bearing bush set

1

735*

Copper seal

1

Silicone grease 1 g

*

Only for Size 15 – 26

**

Only pumps with inlet pressure under the ambient pressure, only pumps with mechanical seal

***

Only for Size 55 – 660, 880

°

Only for mechanical seal

Tab. 16: Spare parts CLE 15 – 660, CLE 880

56

OIC 18en-GB Edition 2020-01

Operating instructions

Содержание CGF

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды