manualshive.com logo in svg

KRAL CGF, Руководство по эксплуатации

Поделиться
Скачать
KRAL CGF Скачать руководство пользователя страница 52

15 Accessories

15.1 Heating

15 Accessories

15.1 Heating

15.1.1

Possible types of heating

The pump can optionally be equipped with a heating system. The manufacturer recommends a heating
system at high-viscosity pumped liquids that do not flow sufficiently if not heated. A flowability that lies
too low can result in excessive power draw or to cavitation or sealing problems.

Possible types of heating:

o

Fluid heating system

15.1.2

Fluid heating system

483

1

1

Fig. 15: Fluid heating system

483

Heating cover

1

Pipe connection

The fluid heating system consists of a heating cover 

483

, attached additionally to the end cover,

through which a heating liquid (for example vapour, thermal oil) flows.

Scope of delivery:

Size 15 – 3550

1 heating cover

8 socket screws

Tab. 12: Scope of delivery of the fluid heating system

Operating data

Parameter

Unit

Value

Max. pressure

[bar]

18

Max. liquid temperature

[°C]

220

Tab. 13: Operating data fluid heating system

Dimensions and steam amount

The following table shows the dimensions of the connections of the fluid heating system, depending on
the outer housing as well as the required steam amount for a temperature increase of 50 °C in a heat-
ing-up period of 1 h.

52

OIC 18en-GB Edition 2020-01

Operating instructions

Содержание CGF

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды