KRAL BEM 300 Series Скачать руководство пользователя страница 23

Страница: 23 / 48

Operating Instructions

OIE 15en Edition 2019-12 HW 2.0/SW 2.0

Safety instructions for commissioning

Commissioning

Safety instructions for commissioning

Checking the electronic unit

Taking the electronic unit out of operation

► Switch off the power supply of the system.

Note

: All the settings and total values are retained when the electronic unit is switched off or the power

supply fails. After operation is resumed, instantaneous values (Q, T) are recalculated.

The following safety instructions must be observed during commissioning:

□

The following qualifications are required for commissioning:

▪

Practical electrotechnical training

▪

Knowledge of the safety guidelines at the workplace

▪

Knowledge of the electrotechnical safety guidelines

Check

Procedure

Installation

► Check that the electronic unit is seated firmly.
► For wall and pipe mounting as well as mounting on volu-

meter: Ensure that the rear device cover and cable
entries seal properly.

Electrical installation

1. Ensure that the system is disconnected.
2. Remove the rear device cover.
3. Check that the wiring of the power supply at the terminal

panel is firm.

4. Check the connection of the power supply to the system.
5. Check the numbering of the pick ups.
6. Check the assignment of the pick ups.
7. Check the connections of the pick ups.

Function test

► Switch on the power supply.

The start message is displayed on the display unit.
At the latest after 3 seconds the "1.01 Display Volume-
ter A" page is displayed.

DANGER

Risk of death resulting from electric shock.

► The electronic unit may only be separated from the power supply by an authorized electrician.

Содержание BEM 300 Series

















































Результаты поиска

Содержание BEM 300 Series

Отзывы:

Бренды по названию

Популярные бренды

KRAL BEM 300 Series, Руководство по эксплуатации

Результаты поиска

Содержание BEM 300 Series

Отзывы:

Бренды по названию

Популярные бренды