background image

Hussong Mfg. Co., Inc. • CSK-335S 

 Report No.: 0216GN012S • Rev. 04, August 2015

HUSSONG MANUFACTURING CO., INC.

 

ͷ

Do not store or use gasoline or other 

flammable  vapors  and  liquids  in  the 

vicinity of this or any other appliance.

 

ͷ

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.

 

ͷ

Installation and service must be performed 

by a qualified installer, service agency or 

the gas supplier. 

    WARNING:

FIRE OR EXPLOSION HAZARD

Failure  to  follow  safety  warnings  exactly 

could  result  in  serious  injury,  death,  or 

property damage.

This  appliance  may  be  installed  in 

an  aftermarket,  permanently  located, 

manufactured  home  (USA  only)  or  mobile 

home, where not prohibited by local codes.
This appliance is only for use with the type 

of  gas  indicated  on  the  rating  plate.  This 

appliance  is  not  convertible  for  use  with 

other gases, unless a certified kit is used.

INSTALLER: Leave this manual with the appliance.  

CONSUMER: Retain this manual for future reference.

CHASKA-335S

Model #CSK-335S

Direct Vent Gas Fireplace Insert

Tested &
Listed By

O-T L

US

C

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

Installation and 

Operation Manual

DANGER

HOT GLASS

 WILL

CAUSE BURNS

DO NOT TOUCH

 GLASS

UNTIL COOLED

NEVER

 ALLOW CHILDREN

TO TOUCH GLASS

A  barrier  designed  to  reduce  the  risk  of  burns 

from the hot viewing glass is provided with this 

appliance and shall be installed for the protection 

of children and other at-risk individuals.

English and French installation manuals are 

available through your local dealer. Visit our website 

 

www.kozyheat.com

 or scan the QR code for our mobile app.

Les manuels d’installation en français et en anglais sont 

disponibles chez votre détaillant local. Visitez 

www.kozyheat.

com ou scannez ce code QR pour notre application mobile.

Содержание CHASKA CSK-335S


































Отзывы: