background image

 - 10 -

Mounting the Circuit Board

Building the main circuit board

Starting from the shorter parts, attach and solder the parts while referring 
to the list of mounted parts and the mounting diagram. Be careful not to get 
the parts mixed up. The jacks and volume controls are soldered on last.
You might find it easy to work by following the steps below.

Soldering the parts

1.  Solder the resistors (21–39).

The position and fixed number of parts will vary, depending on the 
variation you decided to build (CLEAN, OVERDRIVE or DISTORTION).
Install the parts according to the model you will be building, while 
checking the “List of mounted parts” on page 7.

R19

R20

R21

R22

R23

R24

R16

CLEAN

OPEN

0

OPEN

OPEN

0

0

10K

OVERDRIVE

OPEN

0

OPEN

OPEN

0

0

240

DISTORTION

4.7K

15K

0

0

OPEN

OPEN

15K

2.  Solder the diodes (5, 6).

The diodes have polarities, so make sure to mount them in the right 
direction.

Symbol

Part´s appearance

3.  Solder the inductor (40).
4.  Solder the operational amplifier socket (3).

Be sure to install the part in the correct direction.

5.  Install the operational amplifier (2) in the socket.

Install the pin #1 of the operational amplifier (shown with a mark) so 
that it lines up with the dot on the circuit board. Be sure to mount the 
part in the correct direction.

6.  Solder the J-FET (4).

Be sure to mount the parts in the correct direction.

7.  Solder the connectors (41–43).

Be sure to mount the parts in the correct direction.
If the symbols do not match those shown on the circuit board, the 
connector is facing the wrong way.

8.  Solder the slide switch (46).
9.  Solder the trimmer potentiometer (50).
10.  Solder the capacitors (7–20).

Mount the parts beginning with the shorter ceramic capacitors, and 
then the film capacitor, and finally the electrolytic capacitor.
The electrolytic capacitors have polarities, so make sure to mount 
them in the right direction.
The position and fixed number of parts will vary, depending on the 
variation you decided to build. Install the parts according to the model 
you will be building.

C2

C19

C8

C9B

C16

CLEAN

0.1uF

OPEN

1uF

OPEN

OPEN

OVERDRIVE

0.01uF

OPEN

           0.047

uF

      O

PEN

            0

.22uF

DISTORTION

0.01uF

1uF

0.047uF

0.01uF

0.0082uF

Содержание Nu:tekt OD-KIT

















Отзывы: