77
Song Play operating mode
Page 3 - Mixer: FX send C/D
Note:
When
you
stop
the
Song,
or
select
a
different
Song,
the
default
effects
are
selected
again.
You
can,
however,
stop
the
Song,
change
the
effects,
then
start
the
Song
again.
Edit
the
Song
in
Song
mode
to
permanently
change
the
effects.
Here
is
the
edit
procedure:
1.
Use
the
VOLUME/VALUE
(A–H)
buttons
to
select
a
track.
2.
Use
the
F
‐
1–F
‐
4
buttons
to
select
a
parameter
for
that
track.
3.
Use
the
TEMPO/VALUE
controls
to
change
the
parameter’s
value.
Parameters
000
No
effect.
Only
the
direct
(uneffected)
sig
‐
nal
goes
to
the
outputs.
127
100%
effect.
The
direct
(uneffected)
and
effected
signals
go
to
the
outputs
with
the
same
level.
PAGE 3 - MIXER: FX SEND C/D
This
page
lets
you
set
the
level
of
the
track’s
direct
(uneffected)
signal
going
to
the
C
and
D
Internal
FX
processors.
Note:
You
can
access
this
page
only
while
editing
the
Sequencer
2,
and
the
parameter
is
set
to
“CD
Mode”
(see
Use
the
TRACK
SELECT
button
to
switch
from
tracks
1–8
to
tracks
9–16.
Here
is
the
edit
procedure:
1.
Use
the
VOLUME/VALUE
(A–H)
buttons
to
select
a
track.
2.
Use
the
F
‐
1–F
‐
4
buttons
to
select
a
parameter
for
that
track.
3.
Use
the
TEMPO/VALUE
controls
to
change
the
parameter’s
value.
Parameters
000
No
effect.
Only
the
direct
(uneffected)
sig
‐
nal
goes
to
the
outputs.
127
100%
effect.
The
direct
(uneffected)
and
effected
signals
go
to
the
outputs
with
the
same
level.
PAGE 4 - FX: A/B SELECT
This
page
lets
you
select
the
A
and
B
effects.
Usually,
the
A
effect
is
a
reverb,
while
the
B
effect
is
a
modulat
‐
ing
effect.
Effects
A
and
B
are
usually
reserved
to
Sequencer
1.
You
can,
however,
create
Songs
by
using
all
four
effects
in
Song
mode.
Depending
on
the
status
of
the
parameter,
this
effect
pair
could
be
reserved
to
Sequencer
2,
too
(see
Note:
When
playing
back
a
Song
that
makes
use
of
all
four
effects
(A–D),
you
can’t
edit
any
effect
parameter.
These
parameters
appear
greyed
out
in
the
display.
Note:
When
you
stop
the
Song,
or
select
a
different
Song,
the
default
effects
are
selected
again.
You
can,
however,
stop
the
Song,
change
the
effects,
then
start
the
Song
again.
Edit
the
Song
in
Song
mode
to
permanently
change
the
effects.
A, B
Effects
assigned
to
the
A
and
B
effect
processors.
Usu
‐
ally,
A
is
the
reverb,
while
B
is
the
modulating
effect
(chorus,
flanger,
delay…).
For
a
list
of
the
available
effects,
see
ModTrk (Modulating Track)
Source
track
for
modulating
MIDI
messages.
You
can
modulate
an
effect
parameter
with
a
MIDI
message
generated
by
a
physical
controller.
B>Asend (B>A Send)
Amount
of
the
B
effect
going
back
to
the
input
of
the
A
effect.
PAGE 4 - FX: C/D SELECT
This
page
lets
you
select
the
C
and
D
effects.
Usually,
the
C
effect
is
a
reverb,
while
the
D
effect
is
a
modulat
‐
ing
effect.
Effects
C
and
D
are
usually
reserved
to
Sequencer
2
and
the
Realtime
tracks.
You
can,
however,
create
Songs
using
all
four
effects
in
Song
mode.
Depending
on
the
status
of
the
parameter,
Sequencer
2
might
also
use
the
A/B
effect
pair
(see
80).
Содержание microARRANGER
