Korg Electronic Keyboard, Руководство по параметрам

Страница: 111 / 1127

Program P7: KARMA 7–2: MIDI Filter/CC Offset
101
These settings do not affect the Dynamic MIDI (7–7)
settings. If you have specified MIDI control data as
the Dynamic MIDI source, it will be valid regardless
of these settings.
After Touch [Off, On]
Specifies whether MIDI aftertouch messages will be
echoed to the tone generator.
Pitch Bend [Off, On]
Specifies whether MIDI pitch bend messages will be
echoed to the tone generator.
Damper (CC#64) [Off, On]
Specifies whether MIDI control change message #64
Sustain (damper pedal) will be echoed to the tone
generator.
JS+Y (JS+Y CC#01) [Off, On]
Specifies whether MIDI control change message #1
(internal joY direction, specified as the
assignment of a real-time control knob, or Vector CC
control) will be echoed to the tone generator.
JS-Y (JS-Y CC#02) [Off, On]
Specifies whether MIDI control change message #2
(internal joystick -Y direction, specified as the
assignment of a real-time control knob, or Vector CC
control) will be echoed to the tone generator.
Ribbon (CC#16) [Off, On]
Specifies whether MIDI control change message #16
(internal ribbon controller, specified as the assignment
of a real-time control knob, or Vector CC Control) will
be echoed to the tone generator.
Other CC [Off, On]
Specifies whether MIDI control change messages other
than the above will be echoed to the tone generator.
Transmit MIDI Filter
Specifies whether filtering will be applied to the MIDI
control data produced by the GE selected for the
KARMA Module. (
See the diagram on the preceding
page, “KARMA Receive/Transmit Filter.”
)
On (checked):
The corresponding MIDI data will be
transmitted from the KARMA Module.
Off (unchecked):
The corresponding MIDI data will
not be transmitted from the KARMA Module.
Note: The GE can also automatically produce pitch
bend and various types of control change messages in
addition to note data. Three envelope generators can
also be used to apply time-variant change to velocity,
tempo, duration, and various control changes such as
pitch bend, JS +Y (CC#1) etc.
The data that is output will depend on the settings of
the parameters for the selected GE. For example,
transmitting/filtering pitch bend will produce no
result if the GE has not been designed to produce pitch
bend data. For more information, please see the “Voice
Name List” on page 1041.
Pitch Bend [Off, On]
Specifies whether to transmit the MIDI pitch bend
messages generated by the GE selected for the
KARMA Module.
Note: This setting also applies to the pitch bend
messages that may be produced by CC–A, CC–B,
Envelope 1, Envelope 2, and Envelope 3.
When the KARMA function is on and the KARMA
Module is producing pitch bend data, the pitch
bend range of the program will be controlled as
follows.
The pitch bend range specified within KARMA GE
will automatically be transmitted from the KARMA
Module, and set within the program. This ensures
that the pitch bend data produced by the GE of the
KARMA will function correctly. At this time, the
pitch bend data produced when you operate the
joystick will automatically be optimized so that it
will produce the same bend effect as if the KARMA
were off (in most cases).
CC–A/CC–B [Off, On]
Specifies whether to transmit the various MIDI
messages generated by CC–A/CC–B of the GE
selected by the KARMA Module.
However if CC–A/CC–B are producing pitch bend
messages, these settings will be ignored, and the
“GE Bend” setting will be used.
Tone
generator
KARMA function
OASYS’s controllers
MIDI IN
KARMA Module
Dynamic MIDI
Transmit MIDI
Filter
Receive MIDI
Filter
GE