A Beijer Electronics Group Company
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
Package Check List
Unpack the box, you will find
JetNet 2005/2005f Switch
Quick Installation Guide
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
Overview
J
etNet 2005/2005f Industrial Ethernet Switch, conforming IEEE 802.3 and 802.3u
standard, supports 5 10/100Base TX (JetNet 2005) or 4 10/100TX plus one
100FX Ethernet port (JetNet 2005f). JetNet 2005/2005f adopts slim industrial
design to save rail space of compact system requirement. In order to survive
under harsh environment, JetNet 2005/2005f chooses industrial-grade aluminum
case with IP30 standard protection.
It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetNet 2005/2005f is recommended to be powered by DC24V
(18~32V) from the 2-pin terminal block.
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
A Beijer Electronics Group Company
Package Check List
JetNet 2005/2005f Switch
Quick Installation Guide
JetNet 2005/2005f Industrial Ethernet Switch supports 5 10/100Base TX (JetNet 2005) or 4
10/100TX plus one 100FX Ethernet port (JetNet 2005f). In order to survive under harsh
environment, JetNet 2005/2005f chooses industrial-grade aluminum case with IP30 standard
protection.
It provides one relay output to alarm port break events, which is enabled/ disabled by the
dip switch. JetNet 2005/2005f is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
Installation
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
A Beijer Electronics Group Company
Port Alam
Fault V+ V- DC24
Power Inputs
Fault
V-
V+
V-
Relay Output,
Carry ability
1A @24V
Fault
V+
2. Connecting the Fiber Port (JetNet 2005f):
Connect the fiber port on your JetNet
2005f to another Fiber Ethernet device, by following the figure below. Wrong connection
will cause the fiber port not working properly.
！
This is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
P1 to P5
(Pin1 ~5)
Pin No. # Status Description
To enable port break alarm at this port.
ON
Off
To disable port break alarm at this port.
NO
1 2
5
4
3
Alarm Switch
DIP Switch Settings for Alarm Relay Output
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of five (5) years from the date of delivery provided that the
Product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Connecting to Network
1. Connecting the Ethernet Ports:
Connect one end of an Ethernet cable into the UTP
port of JetNet 2005/2005f, while the other end is connected to the attached networking
device. All UTP ports support auto MDI/MDIX function. The LNK / ACT LED will turn
Yellow for 10M Ethernet or Green for 100M Ethernet.
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
Package Check List
JetNet 2005/2005f Switch
Quick Installation Guide
Support
JetNet 2005/2005f Industrial Ethernet Switch supports 5 10/100Base TX (JetNet 2005) or 4
10/100TX plus one 100FX Ethernet port (JetNet 2005f). In order to survive under harsh
environment, JetNet 2005/2005f chooses industrial-grade aluminum case with IP30 standard
protection.
It provides one relay output to alarm port break events, which is enabled/ disabled by the
dip switch. JetNet 2005/2005f is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
Installation
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
DIP Switch Settings for Alarm Relay Output
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time Korenix global service center's e-mail is
[email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Wiring the Relay Output
The relay output alarm contacts are in the middle of
the terminal block connector as shown in the figure.
By inserting the wires and set the DIP switch of Port
Alarm to "ON", relay output alarm will detect any
port failures, and form a short circuit. The alarm
relay output is "Normal Open".
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+
and V- contact on the terminal block connector
2. Tighten the wire-clamp screws to prevent the DC
wires from being loosened.
Notes: The recommended working voltage is DC24V
(DC18~ 32 V)
Grounding JetNet 2005/2005f Switch
There is one grounding screw on the bottom side of
JetNet 2005/2005f. Connect the frame grounding of
switchto the grounding surface to ensure safety
andprevent noise to interfere communication.
