5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
Support
workmanship for a period of five (5) years from the date of delivery provided that the
Product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time Korenix global service center's e-mail is
[email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Connecting to Network
1. Connecting the Ethernet Ports:
Connect one end of an Ethernet cable into the UTP port
of JetCon 3401G, while the other end is connected to the attached networking device. The
UTP ports support auto MDI/MDIX function. The Speed LED will turn on for 1000M link
and blinking for 100Mbps link; the LNK/ACT LED will turn on for link up and blinking
for packet transmits and receives.
2. Install Gigabit SFP transceiver and make the connection:
Connect the fiber port on
your JetCon 3401G to another Gigabit Fiber Ethernet device, by following the figure below.
Wrong connection will cause the fiber port not working properly.
The SFP Fiber port supports 2 LEDs for link/activity and full duplex/collision; once the
gigabit fiber port is link up, the link LED will be trigger to “ON”.
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 3401G on the DIN rail.
For information about the DIN Rail installation, please refer to user’s manual.
Wiring the Power Inputs
1. Insert the positive and negative wires into
the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent
the DC wires from being loosened. See Figure-1
Notes: The recommended working voltage is DC24V (DC12~ 48V)
Figure-1
Figure-2
Wiring the Relay Output
The relay output alarm contacts are in the middle of
the terminal block connector as shown in figure-3.
By inserting the wires and settings the DIP switch of
the respective alarm function to “ON”, relay output
alarm will detect port or power fault, and form a
short circuit. The alarm relay output is “Normal Open”. See, Figure -2. For more information,
please refer to the chapter 2-4 and 2-5 of user's manual for more detail information.
Maximum 1A current / DC 24V
Alarm
System
Extra Power
System
+
+
PW1P
W2
Alm 1@ DC24V
Power Event Alm
LLF
Port Event Alm
ON: Enable
Wiring the Earth Ground
In an industrial environment, there might be
devices that generate electromagnetic noise, such
as AC motors, electric welding machine, or a
power generator. These devices will generate
electric noise or surges that might disturb
communications.
To prevent those noises, the device should be well earthed. In the Figure- 3 shows how
to make connection.
Figure-3
Earth Ground
Screw
Earth Ground
Warning: Do not connect to AC line-Natural
+
+
PW1P
W2
Alm 1@ DC24V
Power Event Alm
LLF
Port Event Alm
ON: Enable
！
This is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
# 1
#2
#3
LLF
DIP Switch Settings for Alarm Relay Output and Link
Loss Forwarding
Port Event Alarm
Power Event Alarm
(Link Loss Forwarding)
Pin No. #
Status
ON
ON
ON
Description
To disable Link Loss Forwarding function.
To enable port link down alarm at this port.
To disable port link down alarm at this port.
To enable power failure alarm.
To disable power failure alarm.
To enable Link Loss Forwarding function at both of fiber and
copper port. Once either one of copper or fiber port is
disconnected, the JetCon 3401G will turn-off the other port to
alert the end of attached device forcibly.
Note: Once the LLF is active and the cable event is recovered,
the LLF DIP-switch must be re-triggered to arouse this function.
Off
Off
Off
Package Check List
JetCon 3401G
Quick Installation Guide
CD User Manual
JetCon 3401G Industrial Gigabit Ethernet Media Converter
Quick Installation Guide V1.2
The JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T,
802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit fiber
conversion using store and forward technology. The JetCon 3401G adopts rugged metal case
design to operate in harsh environments (-25~70
o
C); It also provides IP-31 standard
protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can
be enabled/ disabled by dip switch. The fiber port supports SFP socket for several of SFP
transceiver to achieve different link distance.
JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the
6-pin removable terminal block.
Overview
A Beijer Electronics Group Company
A Beijer Electronics Group Company
Software and Documentation
Industrial Networking & Computing
2
01
4 K
ore
nix
Te
chn
olo
gy. S
upp
ort f
or ind
ustrial d
ata communication products pro
vide
d by
ko
ren
ix,
a
Be
ije
r E
lec
tr
on
ics
g
ro
up
c
om
pa
ny
A Beijer Electronics Group Company
Software and Documentation
Industrial Networking & Computing
20
14
Ko
ren
ix
Te
chn
olo
gy.
Supp
ort f
or ind
ustrial d
ata com munication products provide
d by
ko r
eni
x,
a B
eij
er
El
ec
tro
nic
s g
r o
up
c
om
pa
ny
Package Check List
JetCon 3401G
Quick Installation Guide
CD User Manual
JetCon 3401G Industrial Gigabit Ethernet Media Converter
Quick Installation Guide V1.2
The JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T,
802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit fiber
conversion using store and forward technology. The JetCon 3401G adopts rugged metal case
design to operate in harsh environments (-25~70oC); It also provides IP-31 standard
protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can
be enabled/ disabled by dip switch. The fiber port supports SFP socket for several of SFP
transceiver to achieve different link distance.
JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the
6-pin removable terminal block.
Overview
A Beijer Electronics Group Company
Package Check List
JetCon 3401G
Quick Installation Guide
CD User Manual
JetCon 3401G Industrial Gigabit Ethernet Media Converter
Quick Installation Guide V1.2
The JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T,
802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit fiber
conversion using store and forward technology. The JetCon 3401G adopts rugged metal case
design to operate in harsh environments (-25~70oC); It also provides IP-31 standard
protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can
be enabled/ disabled by dip switch. The fiber port supports SFP socket for several of SFP
transceiver to achieve different link distance.
JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the 6-pin
removable terminal block.
Overview
A Beijer Electronics Group Company
