JetCon 3401G V2
Quick Installation Guide v1.0
This is warranty is voided if defects, malfunctions or failures ofthe
warranted Product are caused by damage resulting from force measure
(such as floods, fire, etc.), other external forces such as power
disturbances, over spec power input, or incorrect cabling; or the
warranted productis misused, a
bused, or operated, altered and
repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The productis in compliance with Directive 2002/95/EC and 2011/65/EU
ofthe European Parliament and ofthe Council of 27 January 2003 on the
restriction ofthe use of certain hazardous substances in electrical and
electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our
professional staff are ready to solve your problems at any time Korenix
global service center's e -mail is [email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with
high industrial standard. Korenix warrants thatthe Product(s) shall be
free from defects in materials and workmanship for a period offive (5)
years from the date of delivery provided thatthe Product was properly
installed and used.
Support
DIP Switch Setting
Note:
After adjusting the DIP-switch, please reboot the unit to activate the
new settings.
Dipswitch
Functionality
Switch 1
On: Enable power event alarm
Off: Disable.
Switch #2
On: SFP speed at 100Mbps
Off: SFP speed at 1000Mbps
Switch #3
On: Enable LLF function
Off: Disable.
Wiring the Relay Output
The relay output contacts are in the middle of the terminal block connector
as shown below. By inserting the wires and settings the DIP switch of the
respective alarm function to “ON”, relay output alarm will detect port or
power fault, and form a short circuit. The alarm relay output is “Normal
Open”. For more information, please refer Manual chapter for more detail.
Note:
The relay contact only support 1A current, DC 24V. It does not recommend
apply higher voltage and current that over this specification.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the
terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires loosened.
Connecting to Network
1.
Connecting the Ethernet Port:
Connect one end of an Ethernet cable
into the UTP port of JetCon 3401G V2, while the other end is
connected to the attached networking device. UTP port support auto
MDI/MDIX function. The LNK / ACT LED will turn on and flash to
indicate RJ-45 port link and the packets received and transmitted
from RJ-45.
2.
Install Gigabit SFP transceiver and make the connection:
Connect
the fiber port on your JetCon 3401G to another Gigabit Fiber
Ethernet device, by following the figures below. Wrong connection
will cause the fiber port not working properly.
The SFP Fiber port supports 2 LEDs for link/activity and full duplex/
collision, once the gigabit fiber port is in up, the link LED will be
trigger to”ON”
JetCon 3401G V2 industrial Gigabit Ethernet converter, conforming
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, and IEEE 802.3ab 1000Base-T
supports RJ-45 copper to Gigabit fiber conversion using store and forward
technology. The JetCon 3401G V2 adopts rugged metal case design to
operate in harsh environment (-40~75
°
C). It also IP-31 standard protection.
It features link loss forwarding raise an alarm when a remote fault occurs
and also adopts one relay output to alarm users if a port link or power fails.
Alarm can be enable/disable by dip switch. The fiber port supports SFP
sockets forseveral of SFP transceiver to achieve different link distance.
JetCon 3401G recommend working voltage is DC 48V. (Input range: DC10~
60 V)
Package Check List
JetCon 3401G V2 Industrial Media Converter
Quick Installation Guide
Copyright
Copyright © 2014 all rights reserved. No part of this publication may be
reproduced, adapted, stored in a retrieval system, translated into any
language, or transmitted in any form or by any means without the written
permission of the supplier.
About the Quick Installation Guide
This Quick Installation Guide is intended to guide professional installer to
install and configure the JetCon 3401G V2. It covers procedures to assist
you in avoiding unforeseen problems.
Introduction
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 3401G V2 on
the DIN rail. For information about the DIN Rail installation, please refer
to user’s manual.
Grounding JetCon 3401G V2
There is one grounding screw on the
bottom side of JetCon 3401G V2. Connect the
frame grounding of JetCon 3401G V2 to the
grounding surface to ensure safety and
prevent noise for communication interference.
Installation
Attention:
This is a Class 1 Laser/LED product.
Don’t stare into the Laser/LED
Beam.
