Connecting to Network
1. Connecting the Ethernet Ports:
Connect one end of an Ethernet cable into the UTP port
of JetCon 1302, while the other end is connected to the attached networking device. All
UTP ports support auto MDI/MDIX function. The LNK / ACT LED will turn Yellow for
10M Ethernet or Green for 100M Ethernet.
2. Connecting the Fiber Port:
Connect the fiber port on your JetCon 1302 to another Fiber
Ethernet device, by following the figure below. Wrong connection will cause the fiber port
not working properly.
DIP Switch Settings for Alarm Relay Output
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial standard.
Korenix warrants that the Product(s) shall be free from defects in materials and workmanship
for a period of five (5) years from the date of delivery provided that the Product was properly
installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted Product are caused
by damage resulting from force measure (such as floods, fire, etc.), other external forces such as
power disturbances, over spec power input, or incorrect cabling; or the warranted Product is
misused, abused, or operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0).
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time Korenix global service center's e-mail is
[email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Support
！
This is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
Grounding JetCon 1302
There is one grounding screw on the bottom side
of JetCon1302. Connect the frame grounding of
JetCon1302 to the grounding surface to ensure
safety and prevent noise.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+
and V- contact on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the DC
wires from being loosened.
Notes: The recommended working voltage is DC24V
(DC18~ 32 V).
Wiring the Relay Output
The relay output alarm contacts are in the middle of
the terminal block connector as shown in the figure .
By inserting the wires and set the DIP switch of Port
Alarm to "ON", relay output alarm will detect any
port failures, and form a short circuit. The alarm
relay output is "Normal Open".
Erdung
Port Alarm
Fault V+ V- DC24
Power Inputs
Fault
V-
V+
V-
Relay Output,
Carry ability
1A @24V
Fault
V+
Pin No. # Status
Description
Alarm Switch
ON
Off
To enable port break alarm at this port.
P1 to P3
(Pin1 ~3)
To disable port break alarm at this port.
NO
1 2 3
JetCon 1302 Series Industrial Media Converter
Quick Installation Guide V1.2
JetCon 1302 Industrial Media Converter, conforming IEEE 802.3 and 802.3u standard,
supports 2 10/100Base TX plus one 100FX Ethernet port. JetCon 1302 adopts slim industrial
design to save rail space of compact system requirement. In order to survive under harsh
environment, JetCon 1302 chooses industrial-grade aluminum case with IP30 standard
protection. It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetCon 1302 is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
A Beijer Electronics Group Company
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 1302 on the DIN rail
Package Check List
JetCon 1302 Industrial Media Converter
Quick Installation Guide
JetCon 1302 Series Industrial Media Converter
Quick Installation Guide V1.2
JetCon 1302 Industrial Media Converter, conforming IEEE 802.3 and 802.3u standard,
supports 2 10/100Base TX plus one 100FX Ethernet port. JetCon 1302 adopts slim industrial
design to save rail space of compact system requirement. In order to survive under harsh
environment, JetCon 1302 chooses industrial-grade aluminum case with IP30 standard
protection. It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetCon 1302 is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
A Beijer Electronics Group Company
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 1302 on the DIN rail
Package Check List
JetCon 1302 Industrial Media Converter
Quick Installation Guide
A Beijer Electronics Group Company
JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.1
JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of
forwarding modes – Store and Forward, Modified Cut-through, Pure Converter and
Converter with auto-change modes. The JetCon 2301 adopts rugged aluminum case with
IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh
environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or
-40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes
for alerting remote or central management systems when a remote fault occurs. It also
adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be
enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range
DC10~60V through the 6-pin removable terminal block. The fiber port supports
Single-mode or Multi-mode for providing up to 30KM extended distance transmission.
Overview
Package Check List
JetCon 2301 Industrial Media Converter
Quick Installation Guide
