manualshive.com logo in svg

Kontron CP6500-V, Руководство пользователя

Поделиться
Скачать
Kontron CP6500-V Скачать руководство пользователя страница 96

Configuration

CP6500-V

Page 4 - 16

© 2005 Kontron Modular Computers GmbH

ID 28945, Rev. 01

P R E L I M I N A R Y

2894

5.01.UG.VC.050304/09095

4

4.5.7

I/O Status

The I/O status register describes the local and CompactPCI control signals. The watchdog
status bit indicates the status of the watchdog timer. If the timer is not retriggered within the
previously set time period, the bit is set to ”0” and the watchdog LED lights up. The fail signal
is an output of the power supply and indicates a power supply failure. For the description of the
derate and enumeration signals, please see the interrupt routing register.

4.5.8

Board ID

The board ID register describes the hardware and the board index. The content of this register
is unique for each Kontron CompactPCI board. 

Table 4-21: I/O Status Register

REGISTER NAME

I/O Status Register

ACCESS

ADDRESS

0x286

R

BIT POSITION

MSB

7

6

5

4

3

2

1

0

LS

B

CONTENT

WST

Res.

Res.

Res.

CSLOT

CENUM

CFAIL

CDER

DEFAULT

1

0

0

0

0

0

0

0

BIT

NAME

VAL

DESCRIPTION

0

CDER

0

Indicates power derating (CPCI DEG signal)

1

Power normal

1

CFAIL

0

Indicates a power supply failure (CPCI FAIL signal)

1

Power normal

2

CENUM

0

Indicates the insertion or removal of a hot swap system board (CPCI ENUM)

1

No hot swap event

3

CSLOT

0

Indicates that the board is installed in a system slot

1

Indicates that the board is installed in a peripheral slot

4

0

Reserved

5

0

Reserved

6

0

Reserved

7

WST

0

Indicates that a Watchdog timeout has occurred

1

Indicates that no Watchdog timeout has occurred

Table 4-22:  Board ID Register

REGISTER NAME

Board ID Register

ACCESS

ADDRESS

0x288

R

BIT POSITION

MSB

7

6

5

4

3

2

1

0

LSB

CONTENT

BID7

BID6

BID5

BID4

BID3

BID2

BID1

BID0

DEFAULT

0

1

1

1

0

0

0

0

Содержание CP6500-V

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды