manualshive.com logo in svg

Kontron CP6500-V, Руководство пользователя

Поделиться
Скачать
Kontron CP6500-V Скачать руководство пользователя страница 85

CP6500-V

Configuration

ID 28945, Rev. 01

© 2005 Kontron Modular Computers GmbH

Page 4 - 5

P R E L I M I N A R Y

2894

5.01.UG.VC.050304/09095

4

4.1.7

Serial Ports COM1 and COM2 Jumper and Resistor Settings

4.1.7.1

COM1 Jumper and Resistor Setting

The serial interface COM1 (J9) may be configured for either RS232 or RS422 using solder
jumpers and appropriate resistors. The following figure and tables indicate the physical
locations of these jumpers and resistors, and their required configurations for the various
operational modes.

Figure 4-1: COM1 Configuration Jumpers and Resistors

The default setting is indicated by using italic bold.

RS422 and RS485 COM1 Termination

When COM1 is configured for RS422 operation and is the last device on the RS422 bus, then
the RS422 interface must provide termination resistance. The purpose of jumpers JP5 and JP7
is to enable this line termination resistor (120 ohm).

The default setting is indicated by using italic bold.

Table 4-7: Resistor Setting to Configure COM1

RESISTOR

RS232

RS422

JP8 (soldered or 0 ohm, 0805 package)

Closed

Open

R311 (4700 ohm, 0603 package)

Open

Open

R330 (soldered or 0 ohm, 0603 package)

Open

Open

Table 4-8: Jumper Setting for RS422 RXD Termination (COM1)

TERMINATION

JP5

ON

Closed (soldered or 0 ohm, 0805 package)

OFF

Open

JP6

JP5

JP8

R330

JP4

JP3

R320

JP7

R329

COM1

R311

Содержание CP6500-V

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды