Kontron CP6004-RA Скачать руководство пользователя страница 34

Страница: 34 / 78

Boot Setup

CP6004-SA/-RA/-RC/CP6004X-SA

Page 28

ID 1053-6161, Rev. 3.0

D R A F T — F O R I N T E R N A L U S E O N L Y

3.1.2

Bootup NumLock State

This function is used to set the state of the keyboard’s numlock function after POST.

Default setting: On

3.1.3

Quiet Boot

This function is used to display either POST output messages or a splash screen during boot-up.

Default setting: Disabled

3.1.4

Fast Boot

This function is used to enable or disable boot with initialization of a minimal set of devices re-
quired to launch active boot option..

Default setting: Disabled

3.1.5

CSM16 Module Version

This function provides display-only information concerning the CSM Module and is intended for
internal use only.

3.1.6

GateA20 Active

This function is used to enable or disable GateA20.

Default setting: Upon Request

SETTING

DESCRIPTION

Use this setting to switch on the keyboard’s numlock function after POST.

Off

Use this setting to switch off the keyboard’s numlock function after POST.

SETTING

DESCRIPTION

Disabled

Use this setting to display POST output messages during boot-up.

Enabled

Use this setting to display a splash screen during boot-up.

SETTING

DESCRIPTION

Disabled

Use this setting to disable fast boot.

Enabled

Use this setting to enable fast boot.

SETTING

DESCRIPTION

Upon Request

Use this setting to disable GA20 in the uEFI BIOS.

Always

Use this setting to prevent the system from disabling GA20.

Содержание CP6004-RA















































































Результаты поиска

Содержание CP6004-RA

Отзывы:

Бренды по названию

Популярные бренды

Kontron CP6004-RA, Руководство пользователя

Результаты поиска

Содержание CP6004-RA

Отзывы:

Бренды по названию

Популярные бренды