Kontron CP3010-SA Скачать руководство пользователя

Страница: 71 / 80

D R A F T — F O R I N

T E R N A L U S E O N L Y

www.kontron.com

User Guide

CP3010-SA

9.2.2 Advanced Setup Menu

The Advanced Setup menu provides sub-screens and functions for advanced configuration.

Note:

Setting items on this screen to incorrect values may cause the system to malfunction.

Table 48: Advanced Setup Menu Sub-Screens and Functions

SUB-SCREEN

FUNCTION

DESCRIPTION

Uncore Configuration

GOP Configuration
GOP Driver

Enables/Disables GOP Driver.
If enabled, the GOP Driver will unload VBIOS.
If disabled, GOP Driver will load VBIOS.

South Cluster
Configuration

USB Configuration

Specifies the USB Configuration settings.

EHCI Controller

Controls the USB EHCI (USB 2.0) functions.
One EHCI controller must always be enabled.

xHCI Mode

Specifies the mode of operation of the xHCI controller.

XHCI Link Power
Management

Enables/Disables the XHCI Link Power Management.

Security
Configuration

TXE Configuration
TXE

Enables /Disables Trusted Execution Engine (TXE).

TXE HMRFPO

Enables/Disables TXE HMRFPO.
If “Disabled” is selected, the TXE firmware is temporarily disabled

for the 1

boot cycle. The function is used for cloning via the

kFlash

uEFI Shell command.

TXE Firmware Update

Enables/Disables TXE Firmware Update.

TXE EOP Message

Enables/Disables TXE EOP Message.
If enabled, it sends the EOP Message before entering the OS.

TXE Unconfiguration
Perform

Revert TXE settings to factory defaults.

OS Selection

Selects the operating system (Windows or Linux).

Содержание CP3010-SA

















































































Результаты поиска

Содержание CP3010-SA

Отзывы:

Похожие инструкции для CP3010-SA

Бренды по названию

Популярные бренды

Kontron CP3010-SA, Руководство пользователя

Результаты поиска

Содержание CP3010-SA

Отзывы:

Похожие инструкции для CP3010-SA

Бренды по названию

Популярные бренды