background image

D R A F T   —   F O R   I N 

T E R N A L   U S E   O N L Y

27

www.kontron.com

User Guide

CP3010-SA

2.7.5   Gigabit Ethernet

The CP3010-SA board includes three 10Base-T/100Base-TX/1000Base-T Ethernet ports based on three
Intel® I210-IT Ethernet controllers (two onboard and one on the CP3010-HDD extension module). All
three controllers are connected to the x1 PCI Express interfaces of the Intel® Atom™ processor. Two
Gigabit Ethernet interfaces are individually switchable between front I/O and rear I/O and provide
Wake-on-LAN support. One interface is available on the high-speed I/O extension connector, J7, for
the CP3010-HDD module.

Note:

In order to use the Wake-on-LAN feature, the power supply must not be switched off (+5V
stand-by voltage cannot be used). The CP3010-SA does not turn off the main power supply
after an operating system shutdown in order to support Wake-on-LAN.

Two of the Gigabit Ethernet interfaces are implemented as a standard RJ-45 Ethernet connectors, 
J10A/B on the front panel.

2.7.6   SATA Interfaces

The CP3010-SA provides two SATA ports:

»

One SATA 3 Gb/s port either onboard for the SATA Flash or the CFast card, or on the Compact-
PCI rear I/O interface

»

One SATA 3 Gb/s port either on the CompactPCI rear I/O interface or on the high-speed I/O 
extension connector, J7, for the CP3010-HDD extension modules

2.7.7   Debug Interface

The CP3010-SA provides several onboard options for hardware and software debugging, such as:

»

Four bicolor general purpose LEDs (LED0..3), which indicate hardware failures, uEFI BIOS 
POST codes and user-configurable outputs

»

One JTAG connector, J4, for programming the onboard logic

»

One XDP-SFF, processor JTAG connector, J12, for facilitating the debug and uEFI BIOS soft-
ware development

2.7.8   CompactPCI Interface

The CP3010-SA supports a flexible CompactPCI interface with a hot plug power interface (no PCI hot
swap). In the system slot the PCI  interface is in transparent mode, and in the peripheral slot the Com-
pactPCI interface is isolated so that it cannot communicate with the CompactPCI bus. This mode is
known as "passive mode".

2.7.8.1   Board Functionality when Installed in System Slot

In a system slot, the CompactPCI interface is provided as 32-bit / 33 MHz (66 MHz on request) PCI in-
terface. The CP3010-SA supports up to seven peripheral slots through a CompactPCI backplane.

Содержание CP3010-SA

















































































Отзывы: