Konica Minolta Magicolor 5440 dl Скачать руководство пользователя

Страница: 138 / 164

Status, Error, and Service Messages

128

Error Messages (Warning)

Note

If an error message (

TONER EMPTY

TRANSFER END

, etc.) appears,

print out the configuration page, and then check the status of the other
consumables. For details on printing the configuration page, refer to
“Printing the Configuration Page” on page 96.

This message...

means...

do this...

FUSER LIFE END

The fuser unit has
reached the end of its
life.

Contact Technical Sup-
port with the error infor-
mation.

FUSER LIFE LOW

The fuser unit is near
the end of its life.

If necessary, contact
Technical Support with
the error information.

INCORRECT CART.

The

toner cartridge

is an unapproved
type.

Install a
KONICA MINOLTA toner
cartridge of the appropri-
ate type (AM, EU, AP or
JP), see page 67.

SIZE MISMATCH

A media size mis-
match occurs when

AUTO CONTINUE

(Engine menu) is set
to

Load the correct media
size.

TONER EMPTY

The

toner cartridge

is empty.
(Appears when

ENGINE/TONER
EMPTY CONTINUE

is set)

Replace the toner car-
tridge.

TONER LOW

The

toner cartridge

is low and should be
replaced within 200
pages at 5% cover-
age of letter/A4
pages.

Prepare the specified
color toner cartridge.

Содержание Magicolor 5440 dl





































































































































































Результаты поиска

Содержание Magicolor 5440 dl

Отзывы:

Похожие инструкции для Magicolor 5440 dl

Бренды по названию

Популярные бренды

Konica Minolta Magicolor 5440 dl, Руководство пользователя

Результаты поиска

Содержание Magicolor 5440 dl

Отзывы:

Похожие инструкции для Magicolor 5440 dl

Бренды по названию

Популярные бренды