manualshive.com logo in svg

Konica Minolta FS-501, Руководство по обслуживанию

Поделиться
Скачать
Konica Minolta FS-501 Скачать руководство пользователя страница 26

Mechanical operations

FS-501 Theory of Operation Ver2.0 Sep. 2004

2-16

II Co

mp

o

sit

io

n

/O

p

erat

io

n

4.4

Elevator tray

• The Elevator Tray moves up or down according to certain conditions.

4.4.1

Elevator tray ascent/descent mechanism

• The Elevator Tray is moved up or down by the Elevator Motor that turns forward or back-

ward.

Condition

Elevator Tray

Control

Standby

Stationary at the upper limit posi-
tion.

The position at which the Elevator Tray Upper 
Limit Sensor PQ (PWB-D FN) detects the Eleva-
tor Tray.

Paper fed into 
tray

Lowers to the lower limit position 
depending on the number of 
sheets of paper to be fed into the 
tray.

If the Elevator Tray Upper Limit Sensor PQ 
(PWB-D FN) is activated while paper is being fed 
into the tray, the tray is lowered until the sensor is 
deactivated.

Paper removed 
from tray

Moves up to the upper limit posi-
tion.

If the Elevator Tray Paper Sensor (PC8-FN) is 
unblocked when paper is removed from the tray, 
the tray is raised until the sensor is blocked.

Overload 
detected

Moves down and then up after 
paper has been fed into tray.

Lowers the tray for a given period of time, then 
raises it to the upper limit position. An overcurrent 
is detected in the Elevator Motor during this 
period.

Elevator Tray Upper Limit 
Sensor PQ (PWB-D FN)

Elevator Tray Paper Sensor (PC8-FN)

Elevator Motor (M7-FN)

Elevator Tray

Содержание FS-501







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды