Konica Minolta CM-3700A Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 42

background image

29

Error message

The following error messages may appear when you use SpectraMagic

®

NX CM-S100w, optional color

management software, to control the instrument.
If you see an error message, follow the instructions shown in the table below. If a problem persists, contact
the nearest Konica Minolta-authorized service facility.

Error Messege

Problem / possible cause

Action

Refer to page

Flash Error

The light amount of the
xenon lamp has been
lowered to 50% or less.
• Degradation of the

xenon lamp

• Contamination of the

integrating sphere

Clean the integrating
sphere according to the
instructions in "Cleaning
the CM-3700A and
Accessories" on page
27. If the problem
persists, contact the
nearest Konica Minolta-
authorized service facility.

27

Flash not ready.

The illumination unit has
not been charged.

Contact a KONICA
MINOLTA-authorized
service facility.

-

Flash Error.

The xenon lamp
failed to emit light.
• Xenon lamp dead
• Illumination circuit failure
• Sensor failure"

Retry measurement or
perform recalibration. If the
message persists, contact
the nearest Konica Minolta-
authorized service facility.

-

Incorrect Calibration
Procedure.

The calibration procedure
is not correct.
The count value is not
appropriate for zero (0%)
or while (100%) calibration.

Use the zero calibration
box for zero calibration
and the while calibration
plate for white calibration.

19,20

A/D Error.

A/D conversion failed.
• A/D converter failure
• Circuit failure"

Turn the power off and
then on again. If the
message persists, contact
the nearest Konica Minolta-
authorized service facility.

15

Attached target mask is
for smaller measurement
area than the selected
measurement area.

No target mask is installed
or the target mask
installed is too small.

I n s t a l l   a   t a r g e t   m a s k
suitable  for  or  larger  than
the  measurement  area  or
diameter.

16

Circuit is not
operating properly.

The motor for changing
the measurement
diameter, adjusting the
UV light amount, or
switching between SCI
and SCE is not working.

Turn the power off and
then on again. If the
message persists, contact
the nearest Konica Minolta-
authorized service facility.

15

Not Ready.

Charging for flashing
the xenon lamp is
not complete.

Wait for at least 3 seconds
after the last flash.
If the message persists,
contact the nearest
Konica Minolta-authorized
service facility.

-

«
...
29
30
31
32
33
...
»

Содержание CM-3700A











































Отзывы:

Нет отзывов

Похожие инструкции для CM-3700A

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 28

Бренд: Hach Страницы: 40

POCKET COLORIMETER II

Бренд: Hach Страницы: 142

Бренд: Hach Страницы: 4

Бренд: Hach Страницы: 308

Бренд: Hach Страницы: 158

Бренд: Hach Страницы: 118

POCKET COLORIMETER II

Бренд: Hach Страницы: 116

Бренд: Hach Страницы: 132

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 200

Бренд: JRC Страницы: 308

Бренд: SKF Страницы: 12

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: Liquid Controls Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды