Konica Minolta bizhub 3602P Скачать руководство пользователя страница 8

Страница: 8 / 129

Learning about the printer

Selecting a location for the printer

•

Leave enough room to open trays, covers, and doors and to install hardware options.

•

Set up the printer near an electrical outlet.

CAUTION—POTENTIAL INJURY:

To avoid the risk of ﬁre or electrical shock, connect the power cord

to an appropriately rated and properly grounded electrical outlet that is near the product and easily
accessible.

CAUTION—SHOCK HAZARD:

To avoid the risk of electrical shock, do not place or use this product

near water or wet locations.

•

Make sure that airﬂow in the room meets the latest revision of the ASHRAE 62 standard or the CEN Technical
Committee 156 standard.

•

Provide a ﬂat, sturdy, and stable surface.

•

Keep the printer:

–

Clean, dry, and free of dust

–

Away from stray staples and paper clips

–

Away from the direct airﬂow of air conditioners, heaters, or ventilators

–

Free from direct sunlight and humidity extremes

•

Observe the recommended temperatures and avoid ﬂuctuations.

Ambient temperature 10 to 32°C (50 to 90°F)

Storage temperature

0 to 40°C (32 to 104°F)

•

Allow the following recommended amount of space around the printer for proper ventilation:

Top

305 mm (12 in.)

Rear

100 mm (3.94 in.)

Right side 110 mm (4.33 in.)

Front

305 mm (12 in.)

Learning about the printer

Содержание bizhub 3602P


































































































































Результаты поиска

Содержание bizhub 3602P

Отзывы:

Бренды по названию

Популярные бренды

Konica Minolta bizhub 3602P, Руководство пользователя

Результаты поиска

Содержание bizhub 3602P

Отзывы:

Бренды по названию

Популярные бренды