Konica Minolta bizhub 266 Скачать руководство пользователя страница 155

Страница: 155 / 186

9-3

bizhub 306/266

Primary messages and corrective actions

9.1

If This Message Appears

9.1

Primary messages and corrective actions

Reference

For details on errors and corrective actions when using this machine or the copy function, refer to [User's
Guide Copy].

Message

Cause

Correction action

[Paper jam]
[Open 1st side cover]

A paper jam occurs in this ma-
chine.

Open the cover at the displayed
position, and remove the
jammed paper.

Jammed paper is left in this ma-
chine.

Open the cover at the displayed
position, and remove the
jammed paper again.

[Original doc. jam]
[Open doc. feed cover]

A paper jam occurs in the

ADF

Jammed paper is left in the

ADF

Open the cover at the displayed
position, and remove the
jammed paper.

[Paper jam]
[Open duplex cover]

A paper jam has occurred in

Au-

tomatic Duplex Unit

Open the cover of

Automatic

Duplex Unit

, and remove the

jammed paper.

[FRONT COVER OPEN]
[CLOSE FRONT COVER]

The

Front Cover

of this machine

is opened, or not set securely.

Securely close the

Front Cover

of this machine.

[DOCUMENT COVER OPEN]
[CLOSE DOCUMENT COVER]

An original is loaded into the

ADF

while the

ADF

is opened.

Securely close the

ADF

[DOC.FEED COVER OPEN]
[CLOSE DOC.FEED COVER]

The

Left Cover

of the

ADF

opened.

Securely close the

Left Cover

[Toner empty]

Toner is depleted.
Cannot copy or print data.

Install a new

Toner Bottle

[PAPER EMPTY]
[LOAD PAPER (#XXX)]

Paper-out occurs in the selected
tray.
"#" indicates a tray, and "XXX"
indicates the paper size.

Load paper of the displayed size
into the displayed tray.

[PAPER SIZE ERROR]
[RESET PAPER (#XXX)]

The paper loaded into the tray
does not match the specified
size."#" indicates a tray, and
"XXX" indicates the paper size.

Load the appropriate paper into
the tray.

[COMMUNICATION ERROR
(####)]

•

A communication has failed
due to an error occurred in
this machine.

•

A communication has failed
for certain reasons related to
the fax machine at the desti-
nation.

Press any key to print out a send-
ing or receiving result report and
check the details of this error.
Then, select the Utility screen to
re-configure fax communication
settings.

[REDIAL ALL FAILED]

All attempts to redial failed be-
cause the destination line was
busy or no response was re-
turned.

Press any key to check the line
status of the destination, and re-
try the transmission job.

[MEMORY FULL]

Image data has caused a memo-
ry overflow during fax transmis-
sion.

•

Remove the received data
that is saved in the memory.

•

Transmit a fax using the im-
mediate transmission func-
tion.

[MEMORY FULL]

Image data has caused a memo-
ry overflow during E-mail trans-
mission.

Remove the received data that is
saved in the memory.

Содержание bizhub 266



























































































































































































Результаты поиска

Содержание bizhub 266

Отзывы:

Бренды по названию

Популярные бренды

Konica Minolta bizhub 266, Руководство пользователя

Результаты поиска

Содержание bizhub 266

Отзывы:

Бренды по названию

Популярные бренды