Kongsberg RV-2 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 66

background image

Maintenance manual

KONGSBERG PROPRIETARY.

This document and its accompanying elements contain KONGSBERG

information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited if not
otherwise explicitly agreed with KONGSBERG in writing. Any authorized reproduction, in whole or in part, must
include this legend. ©2022 KONGSBERG - All rights reserved.

P a g e

54 |

66

11.25

Replacement of Limit Switches in Feedback Units

1.

Switch off the main power supply to Motor Controller by turning off the S1 isolating switch.

2.

Remove the cover on the feedback unit.

3.

Identify the defective limit switch [2].

4.

Loosen the screws [1] on top of the switch assembly.

5.

Using a soldering iron, release the wiring from the switch.

6.

Solder the wiring to the new limit switch.

7.

Tighten the screws [1] on top of the switch assembly.

8.

Switch on the power by turning the S1 isolation switch inside the motor controller.

9.

Adjust the limit switch as detailed in chapter

11.16 Adjustment of Limit Switches in Feedback

10.

Install the cover on the feedback unit.

«
...
52
53
54
55
56
...
»

Содержание RV-2



































































Отзывы:

Нет отзывов

Похожие инструкции для RV-2

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Taber Страницы: 27

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Facnor Страницы: 33

Бренд: Hammer Страницы: 42

Бренд: Jet Страницы: 12

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Yuwell Страницы: 2

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренд: H&S Страницы: 56

Бренд: ZOLL Страницы: 48

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды