manualshive.com logo in svg

Kongsberg K-Sync, Руководство по установке

Поделиться
Скачать
Kongsberg K-Sync Скачать руководство пользователя страница 42

42

342741/B

Techniques for determine signal properties

Note

This step only needs to be performed for echo sounders where the signal properties are
not fully specified.

The signal characteristics of the trigger and the feedback signals can be determined
manually if not known. The information gathered during this step should be filled into
the Table Signal Overview

Signal interface overview, page 41

The length of the trigger cable affects the signal strength.

Use an oscilloscope for signal determination.

Prerequisites:

1

Open the K-Sync Application

Settings

→

Installation

→

Installation Settings

dialog

and click

Manage Installed systems

. Check the checkbox for the echo sounder you

want to configure and uncheck all other echo sounders.
If the echo sounder you want to configure is not available, see document 342435 -
K-Sync Operator Manual for echo sounder setup instructions.

2

Verify that the signals to be configured have been set up with the correct terminal
ID in the K-Sync Application

Installation Settings

dialog.

3

Enable the echo sounder being configured in the K-Sync application.

That is, the Enabled checkboxes in the Echo Sounder States area of the application
window should all be unchecked, except for the particular echo sounder being
configured.

4

Make sure that the hydro acoustic sensor that needs to be configured is assigned
to at least one

trigger group

.

In the main application window, under

Trigger group schedule

, click

Configure

to

assign the hydro acoustic sensor to a Trigger group .

5

The signal type (RS-232/TTL) must be set correctly for each core connection to the
I/O module.

KONGSBERG K-Sync Installation manual

Содержание K-Sync









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды