Kongsberg Flexview страница 73 Скачать руководство пользователя | Manualshive

Страница: 73 / 160

background image

922-20207001/1.0

71

Setup menu

You can connect to the Sonar Head using the

Setup

menu. You can also configure the

system, choose your preferences, set up the coordinate system, upgrade the Sonar Head
firmware, or change the Sonar Head IP Address.

How to open

To open this menu, click the menu title.

Description

•

Connect

Click

Connect

to connect to the Sonar Head

and start “pinging”.

Note

When the Sonar Head is running, this menu
command will change to Disconnect.

•

Geo Projection

Click to open the

Geo Projection

dialog box. You can configure the coordinate system

using the

Geo Projection

dialog box.

•

Preferences

Click to open the

Preferences

dialog box. The

Preferences

dialog box is used to set up

system preferences such as units of measure, time format, etc.

•

Head Network Setup

Click to open the

Head Network Setup

dialog box. The

Head Network Setup

dialog

box allows you to change the Sonar Head network parameters, such as the IP address.
This dialog box is only available when the Sonar Head is connected and paused.

•

Head Firmware Configuration

Click to open the

Head Firmware Configuration

dialog box. The

Head Firmware

Configuration

dialog box allows you to upgrade the Sonar Head firmware. This dialog

box is only available when the Sonar Head is connected and paused.

•

System Configuration

Click to open the

System Configuration

dialog box. This dialog box allows you to

set up the Sonar Head, external sensors (such as a GPS or Motion Reference Unit),
and rotators. In addition, you can configure the deployment of the Flexview and
enter mounting offsets.

«
...
71
72
73
74
75
...
»

Содержание Flexview

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flexview

Simrad SP90 Series

Бренд: Kongsberg Страницы: 44

Бренд: Simrad Страницы: 230

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды