Kongsberg Flexview страница 23 Скачать руководство пользователя

Страница: 23 / 160

922-20207001/1.0

Changing the frequency

If you have a high-frequency Flexview transducer, you can change the frequency using
the

Display Widget

Context

There are transducers with varying frequencies available for the Flexview.

Note

The frequency buttons will not appear if you are using a 500 kHz transducer. In addition,
these buttons will not appear in playback mode.

Procedure

Click the

Display Widget

icon.

This icon is located in the
lower-right corner of the sonar
view.

Click one of the buttons to select
a frequency (in kHz).

Click the

Display Widget

icon to

hide the widget.

Note

You cannot select a sonar
application or change the range
until you connect to a Sonar Head
(Click

Setup

→

Connect

Testing operation of the Sonar Head

You can test the operation of the Sonar Head by confirming that sonar data is being
correctly displayed in the

Information Widget

and sonar view. In addition, any errors will

be displayed in the

Output Messages

Head Status

windows.

Prerequisites

The Flexview software must be running.

Tip

Make sure there is sufficient disk space available to complete the survey.

Getting started

Содержание Flexview

































































































































































Результаты поиска

Содержание Flexview

Отзывы:

Похожие инструкции для Flexview

Бренды по названию

Популярные бренды

Kongsberg Flexview, Справочное руководство

Результаты поиска

Содержание Flexview

Отзывы:

Похожие инструкции для Flexview

Бренды по названию

Популярные бренды