Kongsberg cJoy OT Скачать руководство пользователя страница 64

Страница: 64 / 208

Kongsberg cJoy OT

Information messages are only displayed in the Message view.

For an explanation of these messages, refer to the message explanations in Appendix A
at the end of this manual.

If the system tests do not report the same message within a timeout period (usually 20
seconds), the message becomes inactive.

• Inactive Emergency, Warning and Alarm messages must be acknowledged before they

are removed from the Message Line and the Message view.

• Inactive information messages are automatically removed from the Message view.

Presentation of messages

System messages are colour coded in the following way:

• Emergency messages are displayed on red background.

• Alarm messages are displayed on red background.

• Warning messages are displayed on yellow background.

• Information messages are displayed on grey background.

The messages are presented in two different displays:

• The Message line, which shows the most recent Emergency, Alarm or Warning

message that has not yet been acknowledged.

Figure 12

Message line

• The Message view, which contains a list of all the currently active system messages.

To display the Message view, press the

Alarms

button.

385585/C

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды