manualshive.com logo in svg

Kongsberg cJoy OT, Руководство оператора

Поделиться
Скачать
Kongsberg cJoy OT Скачать руководство пользователя страница 45

User interface

Figure 8

Sensor Enable input dialog with two gyrocompasses

Sensor

The name and identification number of each position-reference system and sensor.

Ready

Shows if a position-reference system or sensor is available for use by the system.

•

Green

— Available

•

Red

— Not available

Enable

Allows you to enable (

On

) and disable (

Off

) the signals from a selected

position-reference system or sensor. The position-reference system or sensor must
be available for use (Green

Ready

indicator) before it can be enabled. The system

will automatically disable the position-reference system or a gyrocompass if it is
not available for use (red

Ready

indicator).

Used

Shows which gyrocompass is being used by the system to calculate the vessel's
heading (see

Gyrocompasses

on page 98).

Preference

Allows you to select which gyrocompass (

1

or

2

) is preferred for use by the system

(see

Gyrocompasses

on page 98).

385585/C

45

Содержание cJoy OT

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды