Kongsberg cJoy OT Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 208

background image

Kongsberg cJoy OT

Thruster allocation

The force demand in the surge and sway axes (the force setpoint), and in the yaw axis
(the turning moment setpoint), is distributed to the various thrusters and propellers by
the Thruster Allocation function.

These setpoints are distributed in such a way as to obtain the force and turning moment
required for position and heading control, while also ensuring optimum thruster/propeller
use with minimum power consumption and minimum wear and tear on the propulsion
equipment.

If it is not possible to maintain both the turning moment and the force setpoint due
to insufficient available thrust, priority is normally set to obtain the turning moment
setpoint (heading).

If a thruster/propeller is out of service or de-selected, the “lost” thrust is automatically
redistributed to the remaining thrusters/propellers.

14

385585/C

«
...
12
13
14
15
16
...
»

Содержание cJoy OT

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для cJoy OT

Бренд: Canon Страницы: 2

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Ultratec Страницы: 33

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Watts Страницы: 17

Бренд: FUTABA Страницы: 8

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды