Kongsberg ACS500 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 148

background image

Lithium batteries safety procedures

Part number

Battery type

Battery weight (kg)

Lithium content (g)

290-089010

L10/21 (6/12)

2.2

90

290-082380

L10/21 (6/48)

6.7

270

290-089592

L10/50 (12/42)

6.5

228

290-222071

L10/50 (27/28)

6.6

247

290-083530

L50/10/24

10

438

290-219492

L24 (98)

11

490

290-062447

L50

4.3

175

290-080718

L80

6.8

280

325902

L14.4 (48)

5.9

183

319554

L14.4 (48), cNODE Maxi

5.9

183

355324

L14.4 (48), cNODE Maxi
Exd

5.9

183

347563

L14.4 (24), cNODE Midi

3.0

92

Battery cell manufacturers/types

A transponder lithium battery consists of cells from one or two of the following
manufacturers and types:

• Tadiran TL-2300

• Sonnenschein SL-780

• Saft LS 33600

• Saft LSH 20

• Sonnenschein SL-760

Battery design

A transponder lithium battery consists of several battery cells that are electrical
connected, both in serial and parallel.

There are transponder batteries with different number of cells, voltages and capacity.

All transponder batteries include protection against short-circuits (re-settable fuses) and
reverse current (diodes).

Hazards identification

Short-circuits, overheating, mechanical damage and exposure to water can start chemical
reactions and high currents inside the transponder lithium battery. This can generate
noxious gases and/or danger of explosions. The chemical reactions will continue without
additional supply of oxygen, as the battery cells contain the necessary ingredients for
maintaining the chemical reactions.

397128/C

127

«
...
127
128
129
130
131
...
»

Содержание ACS500





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACS500

Бренд: 2N Страницы: 4

Бренд: Lamtec Страницы: 136

Бренд: Parkside Страницы: 65

Бренд: Partizan Страницы: 7

Бренд: Data Signs Страницы: 23

Бренд: GBD Страницы: 60

Бренд: Fancom Страницы: 23

Бренд: Beninca Страницы: 7

Бренд: MaintTech Страницы: 28

Бренд: GREER Company Страницы: 35

Бренд: Wenglor Страницы: 44

Бренд: Atmel Страницы: 12

Бренд: Anritsu Страницы: 54

Бренд: Governors America Страницы: 6

Бренд: SKF Страницы: 11

Бренд: Quectel Страницы: 97

Бренд: Danfoss Страницы: 162

Бренд: Dudley Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды