Komatsu WB93R-5 Скачать руководство пользователя страница 278 | Manualshive

Страница: 278 / 284

background image

CONFIGURATION FOR THE USE OF THE HAND HYDRAULIC HAMMER

276

6.10.2.2REMOVING THE CONNECTIONS

At the end of work, proceed as follows:

1 - Press the push button (4) to disconnect the circuit, reduce

the engine rpm and stop the engine.

2 - Move the hydraulic controls more than once in all direc-

tions, in order to release any residual pressure from the
circuits of the machine.

3 - Turn the ignition key to position « » and press the ham-

mer control push button (4) to release the residual pres-
sure from the hammer delivery pipe; after releasing the
pressure, press the push button (4) again to disconnect
the circuit.

4 - Turn the ignition key to position « ».

IMPORTANT

q

If the machine is equipped with backhoe servo controls,
to release the residual pressure from the circuits follow
the procedure indicated in the previous paragraph
"6.10.2.1 CONNECTING THE HAND HAMMER"”.

5 - Disconnect the hammer.

CAUTION

q

If quick couplings are not provided, place sealing plugs
with the relevant gaskets on the couplings of the ma-
chine and of the hammer.

WARNING

q

Make sure that the plugs are properly tightened and that
there are no leakages; if the circuit is inadvertently pres-
surized, small leakages can be turned into thin jets that
may perforate the skin or injure the eyes.

q

Always wear thick gloves and safety goggles to carry
out this check.

q

To check the system for leaks, use a piece of cardboard
or a wooden board.

6.10.3 USING THE HAMMER

Consult the specific manual.

6.10.4 MAINTENANCE

The hydraulic system does not require any maintenance operation and inspection other than those prescribed for
the machine.
Regarding the maintenance operations required for the hammer, see the specific operation manual.

RKAB4610

4

https://tractormanualz.com

«
...
276
277
278
279
280
...
»

Содержание WB93R-5





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WB93R-5

Бренд: Baoli Страницы: 112

Бренд: Case Страницы: 41

Бренд: BOXER Страницы: 89

Бренд: BOXER Страницы: 92

Бренд: Doosan Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды