Komatsu WA800-3E0 Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 336

background image

TROUBLESHOOTING

OPERATION

3-150

STARTING ENGINE WITH BOOSTER CABLE

3

When starting the engine with a booster cable, do as follows.

PRECAUTIONS WHEN CONNECTING AND DISCONNECTING BOOSTER CABLE

WARNING

q

When connecting the cables, never contact the posi-
tive (+) and negative (-) terminals.

q

When starting the engine with a booster cable, wear
safety glasses and rubber gloves.

q

Be careful not to let the normal machine and problem
machine contact each other. This prevents sparks from
generating near the battery which could ignite the
hydrogen gas given off by the battery.

q

Make sure that there is no mistake in the booster cable
connections. The final connection is to the engine
block of the problem machine, but sparks will be gen-
erated when this is done, so connect to a place as far
as possible from the battery.

q

When disconnecting the booster cable, take care not
to bring the clips in contact with each other or with the
machine body.

NOTICE

q

For the battery on the normal machine, use a battery with the same capacity as the problem machine.

q

Check that the cable and clips are not damaged or corroded.

q

Connect the clips securely.

q

Check that the lock levers (work equipment, steering) and parking brakes of both machines are at the
LOCK position.

q

Check that all levers are at the neutral position.

CONNECTING THE BOOSTER CABLE

Keep the starting switch of the normal machine and problem machine in the OFF position.

Connect the booster cable as follows, in the order of the numbers marked in the diagram.

1.

Connect the clip of booster cable (A) to the positive (+) ter-
minal of battery (C) on the problem machine.

2.

Connect the clip at the other end of booster cable (A) to the
positive (+) terminal of battery (D) on the normal machine.

3.

Connect the clip of booster cable (B) to the negative (-) ter-
minal of battery (D) on the normal machine.

4.

Connect the other clip of booster cable (B) to the engine
block (E) of the problem machine.

«
...
210
211
212
213
214
...
»

Содержание WA800-3E0

















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA800-3E0

Бренд: Wacker Neuson Страницы: 420

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды