Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 79 / 432

background image

BASIC OPERATION OF MACHINE MONITOR WHEN TROUBLE OCCURS WHILE
OPERATING MACHINE

If any trouble occurs during operation, the standard screen BB
changes to the failure display screen FF.
When ENTER switch is pressed while guidance icon (1) is dis-
played, the “Current Abnormality” screen is displayed.
For the “Current Abnormality” screen and the remedies, see
“CURRENT ABNORMALITY LIST DISPLAY (3-17)”.

REMARK

Guidance icon (1) is displayed only while the machine is stop-
ped completely.
Even when ENTER switch is pressed while the machine is not
stopped completely, the “Current Abnormality” screen is not
displayed.

WARNING DISPLAY

NOTICE
Appearance of any of action levels “L01” to “L04” on the machine monitor indicates presence of an ab-
normality the machine.
Perform the inspection and maintenance according to “ACTION LEVEL DISPLAY (3-16)”.

• These cautions do not guarantee the condition of the machine.

Do not simply rely on the monitor when carrying out checks before starting (daily inspection). Al-
ways get off the machine and check each item directly.

• When the warning caution is displayed in red, if no action is taken, the machine can be seriously

affected. Accordingly, take proper remedies immediately.

• The engine output or engine speed is limited and the machine operation speed may become slow,

depending on the contents of the warning.

OPERATION

EXPLANATION OF COMPONENTS

3-15

«
...
77
78
79
80
81
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Wacker Neuson Страницы: 19

PalletPal Spring

Бренд: Southworth Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды