Komatsu WA380-8 страница 76 Скачать руководство пользователя | Manualshive

Страница: 76 / 432

background image

BASIC OPERATION OF MACHINE MONITOR WHEN STARTING ENGINE WHILE
ENGINE SHUTDOWN SECONDARY SWITCH IS ON

While  engine  shutdown  secondary  switch  (1)  is  ON  (engine
stopped),  even  if  the  starting  switch  is  turned  to  ON  position,
the  screen  shown  in  the  figure  is  displayed  and  the  engine
does not start.
When  engine  shutdown  secondary  switch  (1)  is  turned  OFF
(normal), the machine monitor returns to the standard screen,
and the engine can be started with usual starting switch opera-
tion.
For the function and operating method of engine shutdown sec-
ondary  switch  (1),  see  “ENGINE  SHUTDOWN  SECONDARY
SWITCH (3-109)”.

BASIC OPERATION OF MACHINE MONITOR WHEN STOPPING ENGINE IN NOR-
MAL SITUATION

When starting switch is turned to OFF position, the screen goes out. In the following case, the end screen is
displayed for 5 seconds, and then screen goes out.

End screen with message

If there is any message from your Komatsu distributor, it is displayed on end screen DD for 5 seconds, and then
the screen goes out.
In this case, turn the starting switch to ON position to re-check the message, and if it is the message requesting
response, send back your reply.

EXPLANATION OF COMPONENTS

OPERATION

3-12

«
...
74
75
76
77
78
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: jcb Страницы: 208

Speed King Drive Over- Pit

Бренд: CrustBuster Страницы: 24

Бренд: RAMROD Страницы: 30

Бренд: RAMROD Страницы: 33

Wacker Neuson SM325-27T

Бренд: DINGO Страницы: 20

Caterpillar HY 60

Бренд: Niko Страницы: 35

Бренд: Toro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды