Komatsu WA380-8 страница 62 Скачать руководство пользователя | Manualshive

Страница: 62 / 432

background image

TIRES

HANDLE TIRES

If tires or rims are handled mistakenly, there is danger that the
tire may explode or be damaged, or that the rim may fly off and
cause serious personal injury or death.
To ensure safety, always observe the following.

• Maintenance, disassembly, repair, and assembly of the

tires and rims requires special equipment and special tech-
nology, so always ask your Komatsu distributor to perform
these operations.

• Use only specified tires and inflate them to the specified

pressure.
Appropriate inflation pressure: See “TIRE PRESSURE
(3-222)”.

• When pumping up the tires, check that no other person is

standing  near  the  tire,  and  install  an  air  chuck  with  a  clip
that can be secured to the air valve.
To  prevent  the  tire  inflation  pressure  from  becoming  too
high,  measure  the  pressure  from  time  to  time  with  an  air
gauge while pumping up the tire.

• If the tire inflation pressure goes down abnormally or the

rim parts do not fit the tire, there is a problem with the tire
or rim parts. Always contact your Komatsu distributor for
repairs.

• If the rim parts are not fitted properly when the tire is being pumped up, there is a danger that the rim parts

may fly off, so set up a protective fence around the tire, and do not stand directly in front of the rim. Stand
beside the tread when pumping up the tire.

• Do not adjust the tire inflation pressure immediately after traveling at high speed or operating under heavy

load.

• Never perform welding or light a fire near the tire.
• Always release the inflation pressure from a tire prior to removing rim from tire.
• Before removing the tire from the machine for repairs, remove the valve partially to release the air from the

tire gradually, then remove the tire.

PRECAUTIONS FOR STORING TIRES

Tires for construction equipment are extremely heavy, it may
lead to serious personal injury or death. To maintain safety, al-
ways observe the following.

• As a basic rule, store the tires in a warehouse which unau-

thorized persons cannot enter.
If the tires must be stored outside, always erect a fence
and put up “No Entry” signs.

• Stand the tire at the angle of 60 to 70 ° (A) on a level

ground, and block it securely (1) so that it cannot tip over
or fall over if any person should touch it. Do not lay the tire
on its side. This will deform the tire and cause it to deterio-
rate.

• If the tire should fall over, do not attempt to stop it. Get out of the way quickly.

PRECAUTIONS FOR MAINTENANCE

SAFETY

2-42

«
...
60
61
62
63
64
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Gehl Страницы: 132

Бренд: Case Страницы: 51

Бренд: Case Страницы: 366

Бренд: jcb Страницы: 32

Бренд: AVANT Страницы: 146

Бренд: Terramite Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды