Komatsu WA380-8 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 432

Komatsu WA380-8 Скачать руководство пользователя страница 54

GUARDS

• Guards are installed in the area of the engine to protect personnel from moving parts. These guards should

only be removed by Komatsu service engineer unless specific instructions are given in this manual.

END OF SERVICE LIFE

• For safe dismantling of the machine at the end of service life, please contact your Komatsu distributor.

STOP ENGINE BEFORE CARRYING OUT INSPECTION AND MAINTENANCE

If you are caught or pinched between the work equipment during operation, or exposed to high-temperature or
high-pressure liquids, it is dangerous and may cause serious personal injury or death. Always observe the fol-
lowing.

• Lower the work equipment to the ground and stop the en-

gine before performing any inspection and maintenance.

• Stop the engine (work equipment is lowered to the

ground), and turn the starting switch to ON position. Press
work equipment lock switch (2) to release the work equip-
ment  lock  (the  pilot  lamp  goes  off),  then  operate  work
equipment control lever (1) to RAISE and LOWER position
fully 2 to 3 times to release the remaining pressure in the
hydraulic  circuit.  Then  lock  the  work  equipment  (the  pilot
lamp  lights  up)  by  pressing  work  equipment  lock  switch
(2).
After releasing the remaining pressure in the hydraulic cir-
cuit, turn the starting switch to OFF position.

• Set parking brake switch (3) to ON (operation) position (A)

to apply the parking brake, then put blocks in front of and
behind the tires to prevent the machine from moving.

PRECAUTIONS FOR MAINTENANCE

SAFETY

2-34

«
...
52
53
54
55
56
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов