manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 356

SELECT AND CHECK TIRES

k

k

 WARNING

If a tire or a rim is handled improperly, the tire may burst or
may  be  damaged  and  the  rim  may  be  broken  and  scat-
tered, and that can cause serious injury or death.
 

• Since  maintenance,  disassembly,  repair  and  assembly  of

the  tires  and  rims  require  special  equipment  and  skill,  be
sure to ask a tire repair shop to do the work.

• Never perform welding or light a fire near the tire.

TIRE SELECTION

k

k

 WARNING

Select the tires according to the conditions of use and the weight of the attachments on the machine.
Use only specified tires and inflate them to the specified pressure.
 

Select the tires according to the conditions of use and the weight of the attachments of the machine.
Use the tires shown in the following table.
The travel speed displayed varies with the tire size.

NOTICE
For usability of tires, consult your Komatsu distributor.

• Do not install the tire protector (mesh chain) to rear wheels.
• Do  not  to  use  tires,  such  as  urethane  tires,  that  weigh  remarkably  more  than  the  standard  tires

since the machine can be damaged due to an unexpected load.

• If  a  tire  not  specified  by  Komatsu  is  used,  rim  displacement  between  the  tire  and  rim  may  occur.

Operator comfort, as well, may be degraded.

Tire size

Standard

Front tire: 23.5R25

☆

Rear tire: 23.5R25

☆

Optional

Front tire: 23.5-25-16PR

Rear tire: 23.5-25-16PR

MAINTENANCE PROCEDURE

MAINTENANCE

4-36

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды