manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию, Страница: 349 / 432

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 349

2.

Press down lever (2) and open fan guard (3).

3.

Blow off mud, dirt, leaves, etc. in radiator fins (4) with com-
pressed air.

NOTICE
Steam  or  water  may  be  used  instead  of  the  com-
pressed air.
However,  when  using  the  powerful  steam  cleaning
equipment (high-pressure machine wash) for the heat
exchange equipment (radiator and cooler), keep a suf-
ficient distance to the target machine.
If steam cleaning (high-pressure machine wash) is per-
formed at close distance, there is a danger that the in-
ternal fins of the heat exchange equipment may be de-
formed,  and  this  will  cause  early  clogging  and  break-
age of the equipment.

4.

Check the rubber hoses. If any hose is cracked or hardened by age, replace with a new one. Also check
and tighten all loose hose clamps.

5.

After cleaning, close fan guard (3) and rear grille (1).

METHOD FOR CLEANING FIN WITH ENGINE SIDE COVER OPEN

1.

Open the engine side cover on the right and left sides of the machine.

2.

Insert the air nozzle through the clearance between radia-
tor  (1),  oil  cooler  (2),  aftercooler  (3),  and  air  conditioner
condenser (4) to clean.
Steam  or  water  may  be  used  instead  of  the  compressed
air.

3.

Check  the  rubber  hoses.  If  any  hose  is  cracked  or  hard-
ened  by  age,  replace  with  a  new  one.  Also  check  and
tighten all loose hose clamps.

4.

For  soil  and  dust  fallen  down,  blow  them  out  of  the  ma-
chine according to the following procedure.

MAINTENANCE

MAINTENANCE PROCEDURE

4-29

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов