Komatsu WA380-8 страница 314 Скачать руководство пользователя | Manualshive

Страница: 314 / 432

background image

START ENGINE WITH JUMPER CABLES

k

k

WARNING

• When connecting the cables, never contact the posi-

tive (+) and negative (-) terminals.

• Always wear protective eyeglasses and rubber gloves

when starting the engine by using the jumper cable.

• Be careful not to let the normal machine and failed ma-

chine contact each other.
The sparks caused near the battery could ignite the
hydrogen gas generated from the battery, so be care-
ful not to let it happen.

• Make sure that there is no mistake in the jumper cable

connections.  In  the  last  connection  (to  the  upper
structure  frame),  a  spark  will  be  caused,  connect  the
cable to a spot as far away from the battery as possi-
ble.  (However,  do  not  connect  to  the  work  equipment
since the current does not flow well through it.)

• When disconnecting the jumper cable, take care not to

bring the clips in contact with each other or with the
machine.

• Never start the engine by short-circuiting the starting

motor (jump start).

NOTICE

• The starting system for this machine uses 24 V. Accordingly, the normal machine must be equipped

with a 24 V power supply.

• The sizes of the jumper cables and clips should be suitable for the battery size.
• The battery of the normal machine must be the same capacity as that of the failed machine.
• Check the cables and clips for damage or corrosion.
• Make sure that the cables and clips are firmly connected.
• Check that the lock levers and parking brake levers (if equipped) of both machine are in LOCK posi-

tion.

• Check that each lever is in NEUTRAL position.
• To prevent damage of the electric devices of the failed machine, turn the starting switch of the failed

machine to OFF position, check that the system operating lamp is not lit, and then turn the battery
disconnect switch key to OFF position and remove it before connecting the jumper cable.
For the operating method of the battery disconnect switch, see “BATTERY DISCONNECT SWITCH
(3-126)”.

PROCEDURE FOR CONNECTING JUMPER CABLES

Turn the starting switch and battery disconnect switch of the failed machine, and the starting switch of the nor-
mal machine to OFF position.

TROUBLES AND ACTIONS

OPERATION

3-250

«
...
312
313
314
315
316
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Case Страницы: 22

IMPULSE IR LOADER

Бренд: TC Electronic Страницы: 8

Бренд: Volvo Страницы: 44

Бренд: Volvo Страницы: 130

Бренд: Volvo Страницы: 130

Бренд: Volvo Страницы: 110

Бренд: Volvo Страницы: 113

Бренд: Thomas Страницы: 70

Бренд: Thomas Страницы: 132

Бренд: Toro Страницы: 16

Бренд: Hyundai Страницы: 415

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды