Komatsu WA380-8 страница 312 Скачать руководство пользователя | Manualshive

Страница: 312 / 432

background image

(A): Plug mounting hole (M16: O-ring boss)
(B): Releasing screw hole (M12)

METHOD FOR OPERATING MACHINE IN EMERGENCY

The normal gear shifting operation is performed by electric signals. If there should be a failure in the electrical
system, and the machine does not move, ask your Komatsu distributor.

NOTICE
If an emergency travel operation is needed, ask your Komatsu distributor to perform it.

PRECAUTIONS FOR DISCHARGED BATTERY

k

k

WARNING

• It is dangerous to charge a battery when installed on a

machine. Make sure that it is removed before charg-
ing.

• When checking or handling the battery, stop the en-

gine and turn the starting switch and battery discon-
nect switch keys to OFF positions.

• The battery generates hydrogen gas, and it is danger-

ous that it may explode. Do not bring open flame such
as lighted cigarettes near the battery, or do nothing
that will cause sparks.

• Battery electrolyte is dilute sulfuric acid, and it will at-

tack your clothes and skin. If it gets on your clothes or
on your skin, immediately wash it off with a large
amount of clean water.
If it gets in your eyes, wash the eyes immediately with
clean water, then consult a doctor for medical treat-
ment.

• When handling batteries, always wear protective eye-

glasses and rubber gloves.

• When removing the battery, first disconnect the cable

from the ground (normally the negative (-) terminal).
When installing, first connect the cable to the positive
(+) terminal.
If a tool touches the positive terminal and the chassis,
it is dangerous that it may cause a spark. Be extremely
careful.

• If the terminals are loose, it is dangerous that the de-

fective contact may generate sparks, and it may cause
an explosion.
Install the cable terminals securely.

• When removing or installing the cable terminals,

check which is the positive (+) terminal and which is
the negative (-) terminal.

TROUBLES AND ACTIONS

OPERATION

3-248

«
...
310
311
312
313
314
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: jcb Страницы: 51

TELPRO PANELLIFT 195 T

Бренд: Paragon Pro Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды