manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

"Komatsu WA380-8" - экскаватор с погрузочным оборудованием, требующий правильного ухода и обслуживания. Скачайте бесплатное руководство по эксплуатации и техническому обслуживанию с нашего веб-сайта. Убедитесь, что ваша техника всегда работает на максимальной производительности. (website) - ваш источник для скачивания руководств.

Поделиться
Скачать
background image

HANDLE AIR CONDITIONER

NOTICE

• To  prevent  putting  any  excessive  load  on  the  engine  or  compressor,  use  the  air  conditioner  only

when the engine is running.

• When running in the air conditioner, always start with the engine running at low speed. Never start

the air conditioner when the engine is running at high speed.
It will cause failure of the air conditioner.

• If water gets into the control panel or sunlight sensor, it may lead to unexpected failure, take care

not to let water get on these parts.
In addition, never bring any open flame near them.

• For the auto function of the air conditioner to work properly, always keep the sunlight sensor clean

and do not leave anything around the sunlight sensor that may interfere with its sensor function.

• Where there is dust or bad smell in the using environment of the machine, use the RECIRC mode.
• When turning the cooling on, if the temperature inside the cab is high, open the doors and windows to bring

in fresh air before using the air conditioner.

• When performing inspection and maintenance of the machine equipped with the air conditioner, refer to the

tables in “METHOD FOR CHECKING AND MAINTENANCE AIR CONDITIONER (4-33)”.

• To allow the air conditioner to show its full performance, have inspection and maintenance performed peri-

odically. When adding refrigerant or performing other maintenance, special tools and instruments are nee-
ded, so ask your Komatsu distributor to perform inspection and maintenance.

• When the air conditioner is not used every day, to prevent loss of the film of oil at various parts, run the air

conditioner with the engine at low speed from time to time and perform cooling or dry heating for several
minutes.

• To prevent leakage of the refrigerant from the air conditioner cooling circuit, operate the air conditioner for

several minutes 2 or 3 times a month during the off-season. If the air conditioner is left for a long time when
the refrigerant is leaking, internal rust may occur, causing failure.

• When the temperature inside the cab is low, the air conditioner may not work. In this case, circulate recircu-

lation air to warm the inside of the cab. After that, turn the air conditioner switch ON, the air conditioner will
work.

• If any abnormality is detected in any equipment or sensor used on the air conditioner, the air conditioner

system caution lamp lights up on the monitor screen. If the air conditioner system caution lamp lights up,
ask your Komatsu distributor for inspection and repair.

Ventilation

• When running the air conditioner for a long time, turn the lever to FRESH position once an hour to perform

ventilation and cooling.

• If you smoke when the air conditioner is on, the smoke may hurt your eyes. In such case, open the window

and turn the lever to FRESH for a while for ventilation and cooling to drive smoke out.

Temperature control

For reasons of health, the optimum setting for cooling is considered to be when it feels slightly cool (5 to 6 °C
lower than the ambient temperature) when you enter the cab.
Be careful to select the appropriate temperature.

HANDLE AIR CONDITIONER

OPERATION

3-224

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Takeuchi TL220 Operator'S Manual preview
TL220
Бренд: Takeuchi Страницы: 213
P.Lindberg XN10 Manual preview
XN10
Бренд: P.Lindberg Страницы: 123
Takeuchi TB15FR Operator'S Manual preview
TB15FR
Бренд: Takeuchi Страницы: 18
Barko 495B - SE Service Manual preview
495B - SE
Бренд: Barko Страницы: 99
Toro 22323 Operation And Safety Manual preview
22323
Бренд: Toro Страницы: 13
Compact Power BOXER 427 Operators Operator'S Manual preview
BOXER 427 Operators
Бренд: Compact Power Страницы: 86
Cub Cadet SC2450 Part List Manual preview
SC2450
Бренд: Cub Cadet Страницы: 180
ahlmann AL 65 Operating Instructions Manual preview
AL 65
Бренд: ahlmann Страницы: 138
Azbil SLP-C4A User Manual preview
SLP-C4A
Бренд: Azbil Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды