Komatsu WA380-8 страница 275 Скачать руководство пользователя | Manualshive

Страница: 275 / 432

background image

1.

Set the cutting edge somewhat downward from the hori-
zontal.

2.

While driving the machine forward, tilt the boom control
lever somewhat forward to dig bit by bit as earth and sand
are peeled off.

3.

Keep on driving the machine forward while adjusting the
digging depth by using the boom control lever.
When you perform digging by use of the bucket, avoid ap-
plying the digging force only to one side of the bucket.

LEVELING WORK

NOTICE

• Always drive the machine in reverse when performing leveling work.

When it is unavoidable to drive the machine forward for the leveling work, do not set the bucket
dumping angle to more than 20 °. The work equipment may be damaged.

• Keep ECSS switch turned OFF during leveling work.

1.

Scoop earth and sand into the bucket and then, while driv-
ing the machine in reverse, tilt the bucket forward to dump
earth and sand bit by bit to spread them.

2.

When leveling the ground, tilt the bucket forward so that
the bucket cutting edge touches the ground, then drag the
bucket by driving the machine in reverse.

3.

When performing finish leveling, scoop earth and sand into
the bucket, set the boom to FLOAT position with the buck-
et horizontal, and reverse the machine.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-211

«
...
273
274
275
276
277
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

MT 625 H 75K COMFORT ST5 S1

Бренд: Manitou Страницы: 136

KH500 Versa-Loader

Бренд: Ventrac Страницы: 41

Бренд: Case Страницы: 81

MAGNUM SIGNATURE SERIES

Бренд: Norfield Страницы: 6

Бренд: AVANT Страницы: 16

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды